
Short answer: An RJ45 SFP transceiver (also called a copper SFP or 1000BASE-T SFP) is a hot-pluggable module that fits a standard SFP port and gives you an RJ45 jack for twisted-pair Ethernet. It contains a copper PHY. It does not convert anything to light; it lets a switch, router or NIC with an SFP cage talk to Cat5e, Cat6 or Cat6A cabling. 1G modules reach 100 m. 10G (SFP+) versions are typically specified for 30 m or 80 m, depending on the module and the cable.
- Standards
- 1000BASE-T (IEEE 802.3ab) for 1G; 10GBASE-T (IEEE 802.3an) for 10G; 2.5G/5GBASE-T (IEEE 802.3bz) on multi-rate modules.
- Cable
- Cat5e or better for 1G. Cat6A recommended for 10G.
- Biggest real-world risks
- Host-side mode mismatch (SGMII vs 1000BASE-X), EEPROM coding rejected by the host, and heat in dense ports.
- Best fit
- Connecting copper-only devices (NAS, access points, cameras, legacy gear) to a switch that has spare SFP or SFP+ cages.
What an RJ45 SFP Module Is, and What It Is Not
An RJ45 SFP module uses the same small form-factor pluggable housing as an optical SFP, so it slides into the same cage. Inside, instead of a laser and photodiode, it carries an Ethernet PHY that handles line coding, echo and crosstalk cancellation, clock recovery and auto-negotiation on the copper side. That PHY is also why it behaves differently from a fiber module in power, heat and compatibility.
- It is not a media converter. A common misconception is that the module "bridges copper and fiber". It does not. A switch simply uses a copper SFP in one cage and a fiber SFP in another; the switch does the forwarding between them.
- It is not a DAC. A direct-attach copper cable is a fixed twinax assembly for in-rack links. An RJ45 module works with ordinary structured cabling and patch panels.
- SFP vs SFP+ cages matter. Most SFP+ ports accept 1G SFP modules, but an SFP-only port cannot run a 10G module.
For the fundamentals of the SFP form factor itself, see What Is an SFP Module?
RJ45 SFP Module Types: 1G, Multi-Rate and 10G
"Copper SFP" covers three distinct families. Picking the wrong family is the most common ordering mistake.
| Type | Standard | Copper link speeds | Cable | Typical reach | Typical use |
|---|---|---|---|---|---|
| 1000BASE-T SFP | IEEE 802.3ab | 1G only | Cat5e or better | 100 m | Uplinks and downlinks to gigabit copper devices |
| Multi-rate SGMII SFP (10/100/1000) | IEEE 802.3, SGMII host interface | 10M / 100M / 1G | Cat5e or better | 100 m | Older copper equipment that still negotiates 10/100 |
| 10GBASE-T SFP+ | IEEE 802.3an (some also 802.3bz) | 10G; many modules also 1G, 2.5G, 5G | Cat6A recommended | Commonly 30 m or 80 m (module-dependent) | Server NICs, NAS, 10G copper uplinks |
| Industrial-temperature copper SFP | As above | 1G (typical) | Cat5e or better | 100 m | Outdoor cabinets, factory floors, transport |
Reach and speed support vary by part. Confirm against the datasheet of the exact module before ordering.
Distance and Cabling: What You Can Actually Run
| Copper speed | Minimum practical cable | Standard reach | Note |
|---|---|---|---|
| 1G (1000BASE-T) | Cat5e | 100 m | All four pairs must be good. A damaged pair can silently drop the link to 100M. |
| 2.5G (2.5GBASE-T) | Cat5e | 100 m | Needs a multi-rate module and host support. |
| 5G (5GBASE-T) | Cat6 | 100 m | Same requirement as 2.5G. |
| 10G (10GBASE-T) | Cat6A | 100 m on Cat6A; shorter on Cat6 (up to about 55 m, depending on crosstalk) | SFP+ modules are usually capped lower than the standard (commonly 30 m or 80 m) because of their power budget. |
If you are planning a 10G copper run, read our 10GBASE-T cable guide (Cat6 vs Cat6A, distance limits, copper SFP+ compatibility) and the comparison in 10GBASE-T vs SFP+ data center cabling.
SGMII vs 1000BASE-X: Why a Copper SFP Links in One Switch and Not Another
This is the single most useful thing to understand before buying a 1G copper SFP, and it is missing from most product pages.
The module's PHY talks to the host over a SerDes link. There are two common ways to run it:
- 1000BASE-X mode: the host SerDes runs at a fixed 1 Gbps, with 1000BASE-X (Clause 37) in-band auto-negotiation. The copper side negotiates 1G only. Many 1G-only modules work this way.
- SGMII mode: the PHY tells the host which speed was negotiated on the copper side, so 10M and 100M links are possible. Many Cisco-style 1000BASE-T SFPs (GLC-T class) run SGMII toward the host. Multi-rate 10/100/1000 modules are SGMII by design.
If the module's mode and the port's configuration disagree, you get a link that never comes up, a link that flaps, or one that only works at one speed. Some platforms detect the mode automatically from the module EEPROM; others need the port set explicitly; a few ports only support one mode.
Symptom, likely cause, what to check
| Symptom | Likely cause | What to check |
|---|---|---|
| "Unsupported transceiver" or port stays down | EEPROM coding not accepted by the host | Read the module ID (for example ethtool -m <iface> on Linux, or the switch's transceiver detail command) and compare vendor and part number with what the host expects. See EEPROM checksum error fixes. |
| Module recognized, link down | SGMII / 1000BASE-X mismatch, or port locked to a fixed speed | Check the port media and mode settings, enable auto-negotiation on both ends, and try a known-good patch cable. |
| Link only at 100M or 10M | Damaged pair, forced speed, or wrong module family | Verify all four pairs, remove forced speed or duplex, and confirm the module is multi-rate if 10/100 is required. |
| Link flaps under load | Overheating, or poor cable (uncertified Cat5, long patch chains) | Check module temperature if DOM is supported, leave an adjacent port empty, replace the cable. |
| 10G module negotiates 1G, 2.5G or 5G | Cable or reach beyond what the link can support | Move to Cat6A, shorten the run, and check the module's rated reach (30 m vs 80 m). |
Power, Heat and Latency: The Trade-offs of Copper
A copper SFP carries a full Ethernet PHY, so it generally draws more power and runs hotter than an optical module of the same speed. For a handful of ports this is irrelevant. For a fully populated 48-port switch it decides whether you can use copper SFPs at all.
| Module | Typical power draw | Notes |
|---|---|---|
| 1000BASE-T copper SFP | About 1 to 1.5 W | Some vendors limit the number of copper SFPs per switch or per adjacent port group. |
| 1000BASE-SX / LX fiber SFP | About 0.5 to 1 W | Lower heat, longer reach. |
| 10GBASE-T SFP+ | Commonly 2 to 3 W or more | Hottest of the common SFP+ types. The host must supply the power and airflow. Some switches support only a few per chassis. |
| 10GBASE-SR fiber SFP+ | About 1 W | Much lower heat than 10GBASE-T. |
Typical ranges, not guarantees. Use the datasheet of the exact part and your switch vendor's thermal guidance.
Latency: 10GBASE-T encoding adds on the order of a few microseconds per link (roughly 2.6 µs is commonly cited), against well under one microsecond for fiber SFP+ or DAC. That is irrelevant for most access ports and matters for latency-sensitive workloads such as trading or HPC fabrics.
For a deeper treatment of thermal limits at 10G, see our 10GBASE-T SFP power and heat management guide.
Compatibility and Coding Checklist
Even a technically correct module can be refused by a host that checks the EEPROM vendor string. Before ordering:
- Confirm the cage type: SFP or SFP+. A 10G copper module needs an SFP+ cage.
- Confirm the host supports copper SFPs in that specific port. Some ports on some platforms do not.
- Match the coding to the host brand (for example, Cisco, Juniper, MikroTik or Ubiquiti). See MikroTik coding and UniFi SFP+ module selection for examples.
- Check the host-side mode (SGMII or 1000BASE-X) in the module datasheet against the port's capability.
- Check thermal limits: how many copper modules your switch allows, and whether neighboring ports need to stay free.
- Choose temperature grade: commercial or industrial.
When to Use a Copper SFP, and When Not To
Good fits
- A copper-only device (NAS, access point, camera, legacy equipment) must connect to a switch with a free SFP or SFP+ cage.
- You want to reuse existing Cat5e or Cat6A cabling instead of pulling fiber.
- One chassis needs to serve mixed media, copper in some cages and fiber in others.
- A staged migration where some links move to 10G before the cabling plant does.
Poor fits
- Tightly packed, high-density ports, where copper SFP heat becomes the limit.
- Latency-sensitive links, where the extra PHY delay at 10G matters.
- Short in-rack links: a DAC is cheaper and cooler.
- Distances beyond 100 m, or between buildings: use fiber.
- 25G, 40G or 100G: there is no mainstream RJ45 pluggable for SFP28 or QSFP. Our SFP to RJ45 deployment guide for data centers covers what to use instead.
If you are weighing copper against optical ports in general, our SFP vs RJ45 comparison covers speed, distance, power and cost side by side.
How to Specify an RJ45 SFP Module (RFQ Checklist)
Send these details and an engineer can confirm compatibility before you order:
- Host switch, router or NIC brand and exact model
- Port type (SFP or SFP+) and the port numbers you plan to use
- Required copper speed: 1G only, multi-rate 10/100/1000, or 10G (and 2.5G/5G if needed)
- Host-side mode (SGMII or 1000BASE-X) if you know it
- Coding brand required by the host
- Cable category and link length
- Temperature range (commercial or industrial) and whether DOM is required
- Quantity and whether modules will sit in adjacent ports
Send us your host model and port mode and we will confirm compatibility before you order.
Send Host Model for a Compatibility Check
Frequently Asked Questions
Can an SFP port connect to an RJ45 device?
Yes, with a copper SFP (RJ45 SFP) module. It plugs into the SFP cage and exposes an RJ45 jack for Cat5e or better cable. The host port must support copper SFPs, and a 10GBASE-T device needs a 10G SFP+ copper module in an SFP+ port.
Which connector types do SFP transceivers use?
Fiber SFP and SFP+ modules most often use LC duplex connectors; some older or single-fiber (BiDi) modules use SC. Copper SFP modules use RJ-45. MPO/MTP connectors belong to multi-lane parallel optics such as QSFP, not standard SFP.
How far can an RJ45 SFP module reach?
1000BASE-T SFP modules reach 100 m on Cat5e or better. 10GBASE-T SFP+ modules are commonly specified for 30 m or 80 m, depending on the module's power class and the cable (Cat6A recommended). Always confirm reach on the exact part's datasheet.
Can I use a 1G RJ45 SFP in an SFP+ port?
Usually yes, and it runs at 1G, provided the switch or NIC supports copper SFP modules in that port. Some platforms need the port speed set to 1G. The reverse does not work: a 10G copper SFP+ module cannot run in an SFP-only port.
Why does my copper SFP work in one switch but not another?
The usual causes are a mismatch between the module's host-side mode (SGMII or 1000BASE-X) and the port configuration, EEPROM coding that the host rejects, or a port that does not provide enough power or cooling for the module.
Is a copper SFP hotter than a fiber SFP?
Yes. A copper SFP contains a full Ethernet PHY, so it typically draws more power than a fiber module of the same speed, and 10GBASE-T SFP+ modules draw the most. Dense ports may need airflow, spacing or fewer copper modules per switch.
Related LINK-PP Copper SFP Modules
LP-SFP-MSRC SFP 1000BASE-T Copper 100m RJ-45 Transceiver Module
Cisco GLC-T Compatible 1000BASE-T SFP Copper 100m RJ45 Transceiver Module
LP-SFP-TMRI SFP SGMII 10/100/1000BASE-T Copper 100m RJ-45 Transceiver Module
Juniper Compatible 10/100/1000BASE-T SFP (Copper, 100m, RJ-45, EX-SFP-1GE-T)
LP-SFP-MSRI SFP 1000BASE-T Copper 100m RJ-45 Transceiver Module (Industrial)
Cisco GLC-TE-I Compatible 1000BASE-T SFP Copper 100m RJ45 Industrial Transceiver Module Need 10G copper? Browse our optical and copper transceiver range or send the RFQ details above.
Related Reading
- SFP to RJ45 in the Data Center: Architect's Guide
- SFP vs RJ45: Which One Is Better for Your Network?
- 10GBASE-T Ethernet Cable: Cat6 vs Cat6A, Distance Limits and Copper SFP+ Compatibility
- 10GBASE-T vs SFP+ Data Center Cabling Guide
- 10GBASE-T SFP Power and Heat Management Guide
- What Is an SFP Module?
Standards referenced: IEEE 802.3ab (1000BASE-T), IEEE 802.3an (10GBASE-T), IEEE 802.3bz (2.5G/5GBASE-T); SFP and SFP+ module management per the SFF-8472 family.
-
Nav Menu
-
About LINK-PP
-
All Products
-
Applications



























