HOT CROSS-REFERENCE SEARCHES All Products
HR911105A Cisco GLC-LH-SMD Pulse J1011F21PNL LPJG0926HENL TE 2170704-1 SFP-10G-SR
POPULAR CATEGORIES
Matched Parts (Real-time ES) Use ↑ ↓ to select, Enter to open
ETHERNET DATA CENTER NETWORKING

Ethernet Data Center Network Solutions for Leaf-Spine Fabrics

LINK-PP provides optical and electrical interconnects for Ethernet data center networks, covering server access, leaf-spine fabrics, aggregation links and data center uplinks from 25G to 800G.

ETHERNET DATA CENTER FABRIC SPINE 01 SPINE 02 LEAF 01 LEAF 02 LEAF 03 100G / 200G / 400G / 800G FABRIC LINKS SERVER / NIC 25G / 100G STORAGE 25G / 100G APPLIANCE 25G / 100G SERVER / STORAGE / APPLIANCE ACCESS LEAF-SPINE / CLOS ETHERNET NETWORK
ENDPOINT → LEAF → SPINEDAC · AOC · OPTICAL
Access linksFabric links

Quick answer: An Ethernet data center network connects servers, storage systems, network appliances and external services through a scalable switching fabric. Modern deployments commonly use leaf-spine or Clos architectures, where endpoints connect to leaf switches and each leaf connects to the spine layer to create multiple paths for east-west traffic.

Clos Fabric Architecture
Leaf-Spine
Server Access
25G · 100G
Fabric Links
100G–800G
Physical Media
DAC · AOC · Fiber
ETHERNET DATA CENTER ARCHITECTURE

How Ethernet Data Center Networks Are Structured

The physical interconnect changes by network tier. Server-facing access links prioritize density and short reach, while leaf-spine and uplink connections increasingly depend on high-speed optical interfaces and structured fiber cabling.

SERVER ACCESS 25G / 100G 100G–800G SERVER / NIC ENDPOINT LAYER LEAF SWITCH ACCESS / TOR SPINE FABRIC FABRIC LAYER PHYSICAL INTERCONNECT SFP28 · QSFP28 · DAC · AOC · OPTICS PORT TYPE · MEDIA · REACH · COMPATIBILITY SERVER ACCESS → SWITCH FABRIC → DATA CENTER UPLINK

Server Access Components

  • SERVER → LEAF25G / 100G AccessShort server-facing links using SFP28, QSFP28, DAC, AOC or pluggable optics according to rack layout and port type.
  • MEDIAShort-Reach ConnectivityPassive copper is common for the shortest links; AOC and optics become relevant as reach, routing and structured cabling requirements increase.
  • VALIDATIONHost Port CompatibilityConfirm switch and NIC form factor, electrical mode, EEPROM recognition, FEC behavior and supported breakout configuration.
TRAFFIC MODEL

East-West vs North-South Data Center Traffic

Traffic direction affects where bandwidth is required and how the physical network is built. Leaf-spine fabrics are designed to provide predictable paths for intensive east-west traffic while border and uplink layers carry north-south traffic to external services.

EAST-WEST

Server, Storage and Application Traffic

Server-to-server, virtualization, storage and distributed application traffic typically crosses the leaf-spine fabric and places the greatest demand on internal fabric bandwidth.

Leaf-SpineECMPStorageVirtualization
NORTH-SOUTH

External and Uplink Traffic

Traffic entering or leaving the data center traverses border, aggregation or uplink interfaces where reach, external connectivity and optical link budget become more important.

Border LeafWAN EdgeInternetUplink
ARCHITECTURE COMPARISON

Leaf-Spine vs Traditional Three-Tier Data Center Networks

Both architectures can support Ethernet data centers, but they organize traffic paths and scaling differently. The appropriate design depends on workload patterns, existing infrastructure and operational requirements.

Factor
Leaf-Spine
Traditional Three-Tier
Traffic Pattern
Optimized for high east-west traffic
Historically oriented toward hierarchical north-south traffic
Network Path
Predictable leaf-to-spine paths
Multiple hierarchical switching layers
Scaling
Add leaf or spine capacity
Expand access, aggregation and core tiers
ECMP
Common fabric design element
Depends on routing and topology design
Typical Context
Modern cloud and data center fabrics
Existing enterprise and hierarchical data center networks
ETHERNET SPEEDS

25G to 800G Ethernet in Data Center Networks

Data rate should be selected by network position, server or switch capability, oversubscription target and the expected lifecycle of the fabric rather than by port speed alone.

25G

Server Access

25G SFP28 remains common for server and appliance access where per-host bandwidth requirements do not justify a higher-speed interface.

SFP28DACSRLR
100G

Server and Fabric Connectivity

100G QSFP28 can serve high-bandwidth server access, leaf uplinks and existing leaf-spine deployments.

QSFP28SR4DRLR4
400G

Leaf-Spine and Core Fabric

400G increases fabric capacity for leaf-spine, aggregation and high-density switching environments.

QSFP-DDOSFPQSFP112DR4FR4
800G

High-Capacity Spine Fabric

800G provides higher per-port bandwidth for next-generation spine layers and high-density Ethernet fabrics.

OSFPQSFP-DD800DR82×FR4
MEDIA SELECTION

DAC, AOC and Optical Transceivers in Ethernet Data Centers

Reach is only one factor. Port density, cable routing, structured cabling, serviceability, power and the existing fiber plant also affect the appropriate interconnect.

Media
Reach Class
Best Fit
Main Constraint
Passive DAC
Very Short
Server → Leaf inside the rack
Reach and cable bulk at higher speeds
AOC
Short
Rack-level links and dense cable routing
Fixed optical assembly and field serviceability
SR Optics
Short Optical
Existing multimode fiber environments
MMF reach and connector architecture
DR / FR Optics
Medium
Leaf → Spine and structured SMF fabrics
Fiber type, optical architecture and link budget
LR Optics
Longer
Longer data center and campus links
Link budget, thermal envelope and cost
FIBER SELECTION

Multimode vs Single-Mode Fiber for Data Center Ethernet

Fiber choice should follow the required reach, installed cabling, optical standard and upgrade path. Neither medium is universally correct for every data center link.

MULTIMODE FIBER

Short-Reach Data Center Links

MMF is commonly paired with SR-class optics in short-reach environments with existing OM3 or OM4 cabling. Verify maximum reach, MPO or LC interface requirements and the target optical standard.

SINGLE-MODE FIBER

Structured Fabric and Longer Reach

SMF supports DR, FR and LR-class optical architectures and is often selected where longer reach, structured cabling or a higher-speed migration path is required.

BREAKOUT CONNECTIVITY

Use High-Density Ethernet Ports Across Multiple Lower-Speed Links

Breakout links increase port flexibility, but the host platform must support the required lane mapping, port mode, FEC and software configuration.

400G → 4×100G

High-Density 100G Fanout

Useful where a 400G switch port must connect multiple 100G servers, appliances or downstream switch interfaces.

400G → 2×200G

Dual 200G Connectivity

Applicable on platforms that support the required 200G electrical and breakout mode.

800G BREAKOUT

2×400G or 4×200G

800G ports can provide flexible downstream connectivity when the switch, cable or optics and software support the intended lane configuration.

FORM FACTOR

SFP28, QSFP28, QSFP-DD and OSFP in Ethernet Data Centers

Form factor follows the host port and electrical interface. The same Ethernet speed does not make different module formats mechanically or electrically interchangeable.

SFP28

25G Server Access

Compact single-lane form factor commonly used for 25G Ethernet server and appliance ports.

QSFP28

100G Ethernet

Four-lane pluggable form factor widely used for 100G server, leaf and spine connectivity.

QSFP-DD / QSFP112

400G-Class Platforms

High-density form factors used across 400G Ethernet platforms depending on the host electrical interface and switch design.

OSFP / QSFP-DD800

800G Ethernet

High-bandwidth pluggable formats for next-generation 800G switching platforms with platform-specific thermal and compatibility requirements.

PLATFORM COMPATIBILITY

Data Center Optics Compatibility Is More Than Port Speed

A module must match the host platform at the mechanical, electrical and software layers. Port speed alone does not establish compatibility.

01 · HOST

Mechanical & Electrical Interface

Confirm SFP28, QSFP28, QSFP-DD, OSFP or other host form factor together with lane rate and supported port modes.

Check: Port type · Lane mode · Power class
02 · SOFTWARE

EEPROM, CMIS & NOS Recognition

Verify module identification, memory map behavior, diagnostics and any platform-specific transceiver recognition requirements.

Check: EEPROM · CMIS · DOM
03 · LINK

FEC, Breakout & Optical Specification

Validate host FEC mode, breakout configuration, fiber type, connector and optical reach as part of the complete link.

Check: FEC · Fiber · Reach
Platform Context CiscoAristaJuniperNVIDIA / MellanoxOCP / White-BoxValidate the exact switch, NIC and software combination.
TYPICAL INTERCONNECT BOM

Map Each Data Center Link to the Right Interconnect Family

A BOM should start from the network position and host port before selecting the specific transceiver or cable assembly.

Network Position
Typical Speed
Media
Product Family
Server → Leaf
25G / 100G
DAC · AOC · Optics
SFP28 · QSFP28
Leaf → Spine
100G / 400G
Optical
QSFP28 · QSFP-DD · OSFP
High-Capacity Spine
400G / 800G
Optical
QSFP-DD · OSFP · QSFP-DD800
Rack → Rack
100G / 400G
AOC · SMF Optics
SR · DR · FR
Breakout
400G / 800G
DAC · AOC · Optics
Breakout Assemblies
ENGINEERING CHECKLIST

What to Send for an Ethernet Data Center Interconnect Recommendation

The exact host platform, topology and reach matter more than a generic request for “100G” or “400G optics.”

Host Platform

  • Switch manufacturer and model
  • Server NIC or adapter model
  • Port form factor
  • NOS / firmware version where relevant

Link Requirements

  • 25G / 100G / 200G / 400G / 800G
  • Required link distance
  • Fiber type and connector
  • Straight or breakout configuration

Deployment Requirements

  • Rack and switch count
  • Links per rack
  • Leaf-spine topology
  • Estimated deployment volume
CONNECTIVITY PORTFOLIO

LINK-PP Interconnects for Ethernet Data Center Networks

Select product families by host form factor, Ethernet speed, reach and media architecture before narrowing to a specific SKU.

25G / 100G

Server Access Optics

SFP28 and QSFP28 optical modules for server, appliance and existing high-speed fabric links.

SFP28QSFP28SRLR
400G

400G Optical Transceivers

QSFP-DD, OSFP and related 400G optical architectures for leaf-spine and high-capacity Ethernet fabrics.

DR4FR4LR4QSFP-DD
Explore 400G Optics →
800G

800G Optical Transceivers

OSFP and QSFP-DD800 optical modules for next-generation high-density spine and Ethernet fabric links.

OSFPQSFP-DD800DR82×FR4
Explore 800G Optics →
CABLE ASSEMBLIES

DAC & AOC Interconnects

Short-reach copper and optical cable assemblies for server-to-leaf, rack-level and breakout connectivity.

DACAOCBreakout25G–800G
Explore High-Speed Cables →
FAQ

Ethernet Data Center Networking Questions

What is a leaf-spine data center network?

A leaf-spine data center network is a two-tier switching architecture in which servers and appliances connect to leaf switches and each leaf connects to every spine. This creates multiple paths across the fabric and supports predictable east-west connectivity.

What Ethernet speeds are commonly used in data centers?

25G and 100G are commonly used for server access, while 100G, 200G, 400G and 800G can be used for higher-capacity leaf-spine, aggregation and spine links depending on the host platform and network design.

When should I use DAC, AOC or optical transceivers?

DAC is typically considered for the shortest rack-level links, AOC for short optical links where a fixed cable assembly is acceptable, and pluggable optical transceivers for structured fiber cabling, longer reach and field-replaceable interfaces.

What is the difference between multimode and single-mode data center optics?

Multimode optics are commonly used for shorter links over MMF, while single-mode optical architectures support longer reach and DR, FR or LR-class links. Selection should follow the installed fiber plant, required reach and target Ethernet standard.

Can 400G or 800G ports be broken out to lower-speed links?

Many platforms support breakout configurations such as 400G to 4×100G or 2×200G and 800G to 2×400G. Actual support depends on port mode, lane mapping, FEC, the cable or transceiver implementation and switch software.

What information is required to verify optical compatibility?

Provide the exact switch and NIC model, port speed, form factor, software or firmware version where relevant, required reach, fiber type, connector and breakout mode. Compatibility should be validated against the complete host and link configuration.

NEXT STEP

Turn Your Ethernet Fabric Topology Into an Interconnect BOM

Provide the switch, NIC, link speed, topology and reach. LINK-PP can help map each physical link to an appropriate optical or electrical interconnect option.

For Network Architects

Review the Fabric

Send the server access, leaf-spine and uplink topology together with host port details for interconnect mapping.

Contact Engineering →
For Procurement

Request Data Center Pricing

Provide part numbers, quantities and deployment schedule for pricing, MOQ and lead-time review.

Request a Quote →
For OEM / Integrators

Submit Your Fabric BOM

Submit server-to-leaf and switch-to-switch connectivity requirements for compatible optics, DAC and AOC alternatives.

Submit BOM →