HOT CROSS-REFERENCE SEARCHES All Products
HR911105A Cisco GLC-LH-SMD Pulse J1011F21PNL LPJG0926HENL TE 2170704-1 SFP-10G-SR
POPULAR CATEGORIES
Matched Parts (Real-time ES) Use ↑ ↓ to select, Enter to open
NETWORK INTERFACE CARD CONNECTIVITY

Optical and Copper Connectivity for Ethernet Network Interface Cards

Design the network-side physical interface of Ethernet NICs and network adapters without confusing it with the host-side PCIe connection or the adapter form factor. LINK-PP supports pluggable SFP/SFP28/QSFP interfaces, optical transceivers, DAC/AOC, RJ45 magnetics, LAN transformers and board-edge connectors, while the NIC ASIC, PCIe logic, drivers and offload functions remain part of the adapter platform.

NIC ARCHITECTURE · HOST SIDE vs NETWORK SIDE SERVER / HOST CPU · MEMORY · OS PCIe HOST INTERFACE NIC CONTROLLER / ASIC MAC · QUEUES · OFFLOAD · FIRMWARE NETWORK-SIDE PHYSICAL INTERFACE COPPER NIC PORT ETHERNET PHY MAGNETICS → RJ45 TWISTED-PAIR ETHERNET PLUGGABLE NIC PORT SERDES / HOST ELECTRICAL CAGE → OPTIC / DAC / AOC SFP28 · QSFP28 · HIGH-SPEED PLUGGABLE LINK-PP FOCUS: NETWORK-SIDE CONNECTIVITY · NOT NIC CONTROL LOGIC
HOST → PCIe/OCP → NIC ASICNETWORK SIDE → RJ45 / SFP / QSFP / MEDIA

Quick answer: a network interface card connects a host system to Ethernet through a PCIe host interface, implemented in formats such as a standard add-in card or an OCP NIC, and exposes one or more network-side ports. Copper NICs can use an Ethernet PHY, LAN magnetics and RJ45 connector, while pluggable optical NICs use SFP, SFP28, QSFP28, QSFP112 or OSFP host interfaces depending on the adapter architecture. LINK-PP supplies components for these network-side physical interfaces rather than the NIC controller, PCIe logic, drivers or programmable offload functions.

Ethernet Rate Context

1G · 10G · 25G · 100G+

Network Interfaces

RJ45 · SFP · QSFP

Port Architecture

1 · 2 · Multi-Port

Pluggable Media

Optics · DAC · AOC

WHAT THIS PAGE MEANS BY “NETWORK CARD”

NIC, SmartNIC, Line Card and Embedded Ethernet Are Different Hardware Roles

This page focuses on host-side Ethernet NICs and network adapters. It does not treat switch/router line cards, motherboard Ethernet or programmable SmartNIC features as interchangeable product categories.

Device
Main Role
Typical Host Context
LINK-PP Relevance
NIC / Network Adapter
Connect host to Ethernet network
PCIe or OCP server / appliance
Primary focus: network-side cages, optics, cables or RJ45 magnetics
SmartNIC / DPU
NIC plus programmable or offload functions
Cloud / telecom / infrastructure server
Physical ports may use the same optical or copper media; compute/offload functions are outside LINK-PP scope
Switch / Router Line Card
Chassis forwarding ports
Modular switch / router
Different equipment class; not the main subject of this page
Embedded Ethernet
Onboard network interface
Motherboard / appliance PCB
Related PHY-to-media architecture, but not a replaceable NIC
RJ45 COPPER NIC

PHY + Magnetics + RJ45

Copper Ethernet adapters use a twisted-pair network port whose physical interface depends on PHY, magnetics, connector and thermal design.

RJ45MagneticsTwisted Pair
SFP / SFP+ NIC

1G / 10G Pluggable Ports

Pluggable optical or direct-attach interfaces let the NIC use media selected around the supported rate, host port mode and far-end network.

SFPSFP+Optics / DAC
SFP28 NIC

10G / 25G Adapter Ports

SFP28 network adapters commonly pair the NIC SerDes with a compact pluggable interface for optical modules, DAC or AOC.

SFP2825GDual-Port Possible
QSFP / HIGH-SPEED NIC

40G / 100G / 200G / 400G Context

Higher-speed adapters may use QSFP+, QSFP28, QSFP112 or OSFP depending on the NIC generation, lane architecture and supported port modes.

QSFP28QSFP112OSFP
NIC PORT ARCHITECTURE

Compare Copper, SFP28, QSFP28 and High-Speed NIC Port Paths

The host-side PCIe connection and network-side media interface are separate design domains. The exact SerDes, PHY, cage and module path changes with port type and Ethernet generation.

RJ45 COPPER NIC PCIe HOST NIC ASIC ETHERNET PHY MAGNETICS / RJ45 NETWORK-SIDE DATA PATH NIC ASIC → PHY → MDI → MAGNETICS → RJ45 → COPPER

RJ45 Copper NIC

PHY and Ethernet magnetics between the NIC controller and twisted-pair network

  • HOST SIDEPCIe Host + NIC ControllerThe PCIe host interface and NIC ASIC handle enumeration, queues, drivers and adapter features outside LINK-PP component scope.
  • COPPER PHYEthernet PHY / MDIUse the actual PHY reference design when selecting magnetics, center taps, pin mapping and the board-edge connector.
  • NETWORK SIDEMagnetics + RJ45LINK-PP relevance is strongest at the PHY-to-cable physical interface, including integrated MagJack or discrete transformer architecture.
HOST SIDE vs NETWORK SIDE

PCIe Is the Host Interface; SFP, QSFP and RJ45 Are Network Interfaces

A NIC sits between a PCIe host interface and an Ethernet network interface. The adapter may use a standard PCIe add-in-card or OCP NIC mechanical form factor, while the network side is implemented through SerDes or PHY, cage/connector and external media.

CPU / Memory Host System
→
PCIe Host Interface
→
NIC ASIC MAC / Adapter Logic
→
PHY / SerDes Network Electrical
→
RJ45 / SFP / QSFP External Media
LINK-PP focuses on the network-facing physical connection. PCIe enumeration, drivers, RDMA, SR-IOV, DPDK and other adapter functions remain properties of the NIC platform.
SFP / SFP28 / QSFP HOST ARCHITECTURE

What Sits Inside an SFP, SFP28 or QSFP NIC Port?

A pluggable NIC port is a stack of electrical, mechanical and management layers. The NIC SerDes and host electrical interface drive the cage connector, firmware manages module information and port mode, and the external optic or cable completes the network link.

NIC ASIC / SerDes Lane Generation
→
Host Electrical Port-Specific Interface
→
Connector + Cage Mechanical / EMI
→
Module Management EEPROM / Port Policy
→
Optic / DAC / AOC External Media
This stack applies across SFP, SFP+, SFP28 and QSFP-family NIC ports. The physical form factor does not by itself define every supported Ethernet rate, lane mode, FEC setting or module policy.
Port Layer
Main Function
LINK-PP Relevance
Qualification Focus
NIC SerDes / Port Logic
Generates and receives high-speed electrical lanes
Defines the electrical environment seen by the pluggable host
Lane count, configured port mode and supported host interface
Host Electrical Interface
Connects NIC lanes to the module connector
Must match the intended SFP/QSFP-family host generation
Signal integrity, connector mapping and supported electrical specification
Cage + Connector
Provides retention, shielding and pluggable module interface
Direct LINK-PP board-level component opportunity
Footprint, EMI, bracket alignment, airflow and insertion mechanics
Module Management
Reads identification and controls supported port behavior
Affects optics/cable recognition and compatibility
EEPROM data, firmware policy, module power and port settings
External Media
Completes the link to the far-end Ethernet port
Optical transceiver, DAC, AOC or supported AEC selection
Rate, FEC, wavelength, fiber/cable type, reach and far-end mode
NIC / TRANSCEIVER COMPATIBILITY

Mechanical Fit Does Not Guarantee NIC-to-Module Compatibility

An SFP28 or QSFP28 module can fit the cage and still fail to link because the NIC port mode, lane configuration, FEC, module identification, firmware policy or far-end network does not match the intended connection.

NIC Model / Firmware

Start with the exact adapter model and firmware revision. Different cards using the same cage can expose different supported rates, media and module policies.

Port Rate / Lane Mode

Verify the configured Ethernet rate, number of lanes and any breakout mode before selecting the module or cable.

FEC / Signaling

Confirm the NIC and far end agree on the required FEC and signaling mode for the selected Ethernet generation.

Module Identification

EEPROM data and vendor policy can affect recognition even when electrical and optical parameters are otherwise valid.

Media / Far End

Match wavelength, fiber type, reach, connector, DAC/AOC type and remote port configuration as one link rather than validating the NIC side alone.

RJ45 COPPER NIC

Copper NIC Design Depends on the PHY, Magnetics and Board-Edge Connector Together

For RJ45 Ethernet adapters, the network path runs from the NIC controller through the Ethernet PHY and MDI to the magnetics and RJ45. A footprint match alone is not enough to qualify a replacement magnetic component.

NIC Controller MAC / Adapter Logic
→
Ethernet PHY 100M / 1G / Multi-Gig / 10G
→
MDIPHY Reference Design
→
LAN Magnetics Integrated or Discrete
→
RJ45 Twisted-Pair Network
Review turns ratio, OCL, center taps, insertion/return loss, crosstalk, CMRR, pin assignment, LEDs, shielding, isolation, temperature and mechanical fit against the real PHY design.
Architecture
Board Fit
Main Advantage
Qualification Focus
Integrated MagJack
Compact NIC board edge
Connector + Ethernet magnetics in one assembly
PHY match, height, LEDs, shield, temperature and bracket fit
LAN Transformer + RJ45
Custom transformer / connector placement
Independent electrical and mechanical selection
Routing, OCL, CMRR, pin mapping, isolation and assembly
PORT SPEED vs FORM FACTOR

Form Factor Indicates the Physical Host Interface, Not Every Supported Ethernet Mode

The same physical cage can expose different Ethernet modes on different NICs. Treat the form factor as the physical interface, then verify the adapter's supported rate, lane configuration, breakout behavior, FEC and firmware policy separately.

Design Context
Common Port Family
Mode Context
Always Verify
1G
SFP / RJ45
Single-lane or copper PHY context
NIC port mode, supported media class and far-end Ethernet standard
10G
SFP+ / RJ45
Single-lane pluggable or 10GBASE-T PHY context
Port mode, host support, thermal budget and firmware policy
25G
SFP28
Single-lane 25G host context
Lane rate, FEC, module policy and peer mode
40G / 100G
QSFP+ / QSFP28
Multi-lane aggregate or supported breakout context
Lane mode, breakout support, FEC and far-end configuration
200G / 400G
QSFP112 / OSFP
High-speed multi-lane host context
NIC generation, electrical host, lane mode, FEC, cooling and firmware support
NIC MEDIA SELECTION

Choose Optics, DAC or AOC Around Reach, Cabling and NIC Port Support

Pluggable NIC ports can support more than one external medium when the adapter firmware and electrical host permit it. The media decision should be based on the actual link rather than the cage form factor alone.

Media
Typical NIC Role
Main Advantage
Check Before Use
Optical Transceiver
Structured fiber / longer link / cross-room or cross-building connection
Fiber reach and removal of conductive copper medium from the external link
Rate, wavelength, fiber, reach, FEC, coding and far end
DAC
Short rack / adjacent equipment connection
Low-complexity direct copper path
NIC cable support, gauge, reach, EEPROM and far-end port
AOC
Short-to-medium preterminated optical link
Factory-terminated optical assembly with no field patching required
Rate, reach, bend routing, firmware acceptance and peer port
AEC
Application-specific short active electrical interconnect
Signal conditioning for supported host environments
Explicit NIC support, reach, power and port interoperability
PORT COUNT

Single-Port and Dual-Port NICs Share Host Resources but Expose Separate Network Interfaces

A dual-port adapter gives the host two physical network ports, but application throughput still depends on NIC architecture, PCIe bandwidth, traffic distribution, CPU/memory path and software configuration.

Single-Port NIC

One network-facing port simplifies media selection, cooling and lane allocation while concentrating the adapter's external bandwidth into one link.

Physical path: NIC ASIC → one port → one external link

Dual-Port NIC

Two physical ports may provide separate networks, link aggregation or independent paths depending on the NIC and system configuration.

Verify: PCIe bandwidth · port modes · aggregate traffic · thermal load
HOST BANDWIDTH

A Faster Ethernet Port Still Depends on the NIC Host Interface

The network port is only one end of the data path. Aggregate Ethernet traffic must traverse the NIC controller and host interface, so PCIe generation, lane width and adapter architecture should be reviewed together with port count and line rate.

Network Ports 1 / 2 / Multi-Port
→
NIC ASIC Queues / DMA / Offload
→
PCIe Host Generation + Lane Width
→
CPU / Memory Host Data Path
Do not infer sustained host throughput from the printed Ethernet port rate alone. Evaluate the complete NIC and server architecture using the adapter vendor's supported configuration.
CAGE · EMI · THERMAL

Pluggable NIC Ports Must Be Qualified as an Electrical, Mechanical and Thermal Assembly

The cage and connector affect module retention, EMI shielding, airflow and service access. Higher-power optics or active cables can also change adapter cooling requirements, especially on dense dual-port designs.

Cage / Connector

Confirm footprint, press-fit or connector style, module insertion depth, latch clearance and bracket alignment around the actual NIC PCB.

EMI Shielding

Review cage fingers, panel contact, ground paths and adjacent high-speed structures as part of the adapter-level EMC design.

Module Power

Optics, AOC, AEC and active cables can add power at the port. Verify the NIC's permitted module power and management policy.

Airflow

Module temperature depends on server airflow direction, card placement, neighboring adapters and the NIC heatsink environment.

Port Density

Dual-port or multi-port spacing can increase local heat and constrain cage, heatsink and cable access around the bracket.

NIC MECHANICAL FORM FACTOR

PCIe Add-In Cards and OCP NICs Place Similar Network Ports in Different Mechanical Environments

The network-side optics or RJ45 interface may be similar while the host connector, card outline, bracket and airflow path differ. Treat the server form factor and network port as separate mechanical constraints.

PCIe Add-In Card (AIC)

Low-profile or full-height add-in cards place the network connector at the chassis bracket and rely on the server slot airflow and mechanical envelope.

Check: bracket · card height · cage depth · heatsink · airflow

OCP NIC

OCP NICs use a different server mechanical and connector ecosystem while still carrying PCIe as the host data interface and exposing RJ45, SFP28, QSFP28 or higher-speed external network ports depending on the platform.

Check: OCP generation · port position · host mechanics · cooling
TELECOMMUNICATIONS CONTEXT

NIC Connectivity in Telecom Edge, Network Appliances and Infrastructure Servers

Telecom and network systems use Ethernet adapters to connect compute, packet-processing, storage and control platforms to access, aggregation and service networks. LINK-PP's role remains the physical network connection rather than the application, forwarding or acceleration software.

EDGE COMPUTE

Compact Server Network Ports

SFP28, QSFP28 or RJ45 interfaces can connect edge compute nodes to local aggregation or service networks.

EdgeServerEthernet
NFV / CLOUD

Virtualized Network Infrastructure

High-speed NICs carry host traffic for virtualized telecom workloads, while software acceleration and orchestration remain outside the physical port scope.

NFVCloudNIC
NETWORK APPLIANCE

Firewall / Packet / Service Platforms

Appliances can use optical or copper NICs for uplinks, service ports and traffic interfaces depending on the appliance architecture.

ApplianceOpticsRJ45
STORAGE / CONTROL

Infrastructure Server Connectivity

NIC media should be selected around the actual link distance, switch port, redundancy plan and server thermal environment.

StorageControlCompatibility
NIC TROUBLESHOOTING

Why a NIC Can Be Detected by the Host but the Network Link Stays Down

Separate host enumeration from network-side link qualification. A PCIe device can be present and the driver can load while the external port still fails because the module, cable, port mode, FEC or far-end network does not match.

Symptom
Likely Area
Check First
Do Not Assume
NIC not detected
PCIe / system / firmware
Slot, BIOS, PCIe enumeration, driver and NIC firmware
Optics or RJ45 magnetics are the cause
NIC detected, no link
Port / module / cable / far end
Port mode, media, module detection, cable and peer
Host detection proves the network side is correct
Module detected, no traffic
Rate / FEC / lane / network config
Configured rate, FEC, breakout and far-end mode
EEPROM recognition proves end-to-end interoperability
RJ45 link unstable
PHY / magnetics / cable / thermal
PHY rails, MagJack parameters, cable category, connector and temperature
A matching connector footprint proves the magnetic design
Only one port links
Port config / media / hardware
Per-port mode, module/cable and lane allocation
Both ports share identical configuration automatically
Module overheats
Power / airflow / cage environment
Module power, server airflow, NIC heatsink and adjacent-port load
Form-factor compatibility proves thermal suitability
NIC PORT VALIDATION

Validate Host Detection and Network-Side Connectivity as Separate Layers

The NIC vendor owns PCIe enumeration, driver behavior and adapter firmware. Network-side component qualification should prove the port, cage, magnetics, module or cable remains stable across supported peers, temperatures and traffic conditions.

Host / Adapter

Confirm PCIe or OCP detection, firmware, driver and expected NIC port modes using the adapter vendor's supported configuration.

Owner: NIC / server platform

Pluggable Port

Verify module or cable detection, configured rate, FEC, lane mode, link stability and interoperability with representative far-end ports.

Evidence: link + traffic + supported media

Copper Port

Verify PHY bring-up, auto-negotiation, cable reach, magnetics parameters, packet stability and thermal behavior on RJ45 adapters.

Evidence: PHY / channel qualification

Thermal / EMC

Run representative traffic with the intended optics/cables, adjacent ports and server airflow while validating EMC and temperature margins.

Evidence: system-level qualification

NIC / Host

  • NIC vendor and exact model
  • Add-in card / OCP NIC form factor
  • Port count and supported rates
  • Firmware / driver context
  • Single-port, dual-port or breakout mode

Network Port

  • RJ45 / SFP / SFP28 / QSFP / OSFP
  • Original cage, connector or MagJack part number
  • Optic / DAC / AOC / AEC requirement
  • FEC and lane mode where applicable
  • Fiber type, wavelength and reach

Environment / Supply

  • Module power / thermal budget
  • Server airflow direction
  • Bracket / board-edge mechanics
  • Prototype and annual quantity
  • Lifecycle / second-source requirement
Submit NIC Connectivity Requirements →
PRODUCTS & ENGINEERING RESOURCES

LINK-PP Components for NIC Optical and Copper Interfaces

Pluggable optics and cage hardware are the primary fit for SFP/QSFP NICs, while integrated RJ45 magnetics and LAN transformers serve copper Ethernet adapters.

PLUGGABLE OPTICS

Optical Transceivers

SFP, SFP+, SFP28, QSFP and higher-speed optical modules selected around NIC rate, lane mode, FEC, reach, fiber and compatibility policy.

BOARD-LEVEL HOST

SFP / QSFP Cages & Connectors

Board-edge host hardware for pluggable NIC ports, including connector, cage, shielding, retention, bracket alignment and thermal integration.

DIRECT-ATTACH MEDIA

DAC / AOC / AEC

Short-reach copper and active cable options for supported SFP/QSFP NIC ports, selected around port mode, reach, power and interoperability.

COPPER NIC INTERFACE

RJ45 Connectors & LAN Magnetics

Integrated MagJacks, discrete LAN transformers and modular RJ45 jacks for copper NICs designed around the exact Ethernet PHY and board-edge mechanics.

Telecommunications Parent Solution

Review broader access, transport, aggregation and network-equipment physical connectivity across optical and copper interfaces.

Explore Telecommunications →

Transceiver Cross-Reference Guide

Use a structured compatibility workflow for optical module form factor, rate, reach, coding and platform support.

Read Compatibility Guide →

SFP / QSFP Cage Architecture

Review cage, connector, shielding, mechanical and thermal considerations for pluggable host interfaces.

Read Cage Architecture →

Ethernet MAC vs PHY

Review the boundary between Ethernet frame logic, physical signaling and the external network medium.

Read MAC vs PHY →
FAQ

NIC Connectivity and Transceiver Compatibility Questions

Practical answers for NIC hardware teams, telecom OEMs, integrators and procurement engineers.

Does LINK-PP manufacture complete network interface cards?

No. LINK-PP supplies network-side connectivity components such as optical transceivers, DAC/AOC/AEC, SFP/QSFP cages and connectors, integrated RJ45 magnetics, LAN transformers and modular jacks. The NIC controller, PCIe logic, drivers and adapter firmware belong to the network adapter platform.

Can any SFP28 transceiver work in any SFP28 NIC?

No. Mechanical form factor is only one requirement. The NIC model, configured rate, lane mode, FEC, EEPROM or vendor policy, module power, media type and far-end network must also be compatible.

What is the difference between PCIe and the SFP or QSFP port on a NIC?

PCIe is the host-side interface between the NIC and server. SFP, SFP28, QSFP and similar interfaces are network-side ports that connect the NIC to external optical or direct-attach media.

Why can a NIC detect an optical module but still fail to establish link?

Module detection only confirms part of the management path. Link can still fail because of rate, FEC, lane mode, wavelength, fiber, DAC/AOC type, far-end configuration or firmware policy.

When should a NIC use DAC instead of an optical transceiver?

DAC is commonly useful for short direct connections where both NIC and far-end port explicitly support the cable. Optical transceivers are better suited to links that require structured fiber, different reaches or different optical interfaces.

Does a dual-port NIC always provide twice the usable throughput?

No. Two ports provide two physical network interfaces, but usable throughput depends on NIC architecture, PCIe bandwidth, traffic distribution, host CPU/memory path and software configuration.

How should RJ45 magnetics be selected for a copper NIC?

Start with the exact Ethernet PHY and reference design, then compare turns ratio, OCL, center taps, insertion and return loss, crosstalk, common-mode behavior, isolation, pin mapping, LEDs, shield, temperature and mechanical fit.

NEXT STEP

Move from NIC Port Architecture to a Qualified Network Interface

Send the NIC model, port form factor, Ethernet rate, media requirement and original component information. The adapter name tells us which platform is involved; the network-side electrical, optical and mechanical details determine which LINK-PP component belongs at the port.

For Hardware Engineers

Review NIC Port Compatibility

Share the NIC controller or adapter model, port mode, cage or PHY architecture, module power and thermal constraints.

Contact Engineering →
For Procurement

Cross-Reference Optics, Cages or Magnetics

Provide the original transceiver, cable, cage, MagJack or transformer part number together with quantity and lifecycle requirements.

Request Cross-Reference →
For OEM / Integrators

Submit the NIC Connectivity BOM

Share the network-side BOM, adapter architecture and media requirements for compatibility and sourcing review.

Submit BOM →