Pulse JD2-0010NL Compatible LINK-PP LPJD0012BENL 10/100Base-T Vertical RJ45 Connector Green/Yellow LED
P/N:
LPJD0012BENL
Manufacturer:
LINK-PP
Compatible Brand:
Pulse
Compatible P/N:
LPJD0012BENL
- Compatible Brands: Pulse
- Number of Ports: 1X1
- Speed: 10Base-T,100Base-TX
- PoE: Non-PoE
- Latch: Up
- Mounting Type: THT
- LED Option: Green / Yellow
- Shield EMI Tabs: NO
- Temperature: 0℃ to 70℃
- P/N: LPJD0012BENL
- Manufacturer: LINK-PP
- Compatible Brand: Pulse
- Compatible P/N: JD2-0010NL
Packaging Details:
N.W/pCS:
0.008kg
Package:
Tray
SPQ:
54pcs
Qty/carton:
1296pcs
Carton size:
36.5*33*32cm
G.W/carton:
10kg
Product Specifications
| LINK-PP Part Number: | LPJD0012BENL | Pulse Part Number | JD2-0010NL |
| Part Status | Active | Connector Type | Jack |
| Number of Positions/Contacts | 8p8c (RJ45, Ethernet) | Application-Lan | Ethernet(Non-PoE) |
| Number of Ports | 1x1 Port | Speed | 10/100 Base-T |
| Latch | Up | Cores per Port | 4 |
| Orientation | 180° Angle (Right) | PCB Mount Angle | THT Solder |
| Shield EMI Tabs | Without | LED Option | Green/Yellow |
| PCB | FR4 | PCB Retaining Post | T POST |
| Package Height (Inches/mm) | 0.665/16.90 | Package Length (Inches/mm) | 0.657/16.70 |
| Package Width (Inches/mm) | 0.630/16.00 | Temperature | 0℃ TO 70℃ |
| Bst Circuit | Yes | AutomDX | YES |
| Diodes | No | Contact Mating Area Plating | GOLD 6u"/15u"/30u" |
| Turns Ratio RX/TX | 1CT:1CT | Configuration RX/TX | T,C |
Product Engineering Overview
The LINK-PP LPJD0012BENL is a 10/100BASE-T vertical (180°) RJ45 jack with integrated magnetics, a single port and green/yellow LEDs. Its through-hole, tab-up construction places the cable opening above the PCB and is intended for embedded boards and panel-mounted enclosures that cannot use a right-angle edge jack.
The 16.90 mm overall height, the 16.15 mm body width shown on the mechanical sheet and the LED light-pipe positions drive the panel and enclosure design; check them before layout release.
Design Positioning and Qualification
This page does not establish a verified cross-reference to another manufacturer's connector. Other LINK-PP catalog entries are separate product pages; a shared port count, outline or LED colour is not evidence of electrical or mechanical interchangeability. Qualify the actual host board and the complete interface, including the transformer where the design uses one.
Electrical and Mechanical Integration
The drawing lists 1CT:1CT, 350 µH minimum OCL at 100 kHz, 0.1 V and 8 mA, and 1500 VAC hipot.
- Vertical assembly: The mating face is parallel to the PCB. Check the panel opening, latch-release access and cable bend radius inside the enclosure, and keep the tall jack away from components that would block the cable.
- LED circuit: Green is the left LED and yellow the right LED. The drawing gives 1.8-2.6 V forward voltage at 20 mA, so size the series resistors from the driver supply and align the light pipes with the panel.
- PCB and soldering: Use the suggested land pattern, plated-hole sizes and pin-1 datum from the mechanical sheet. Follow the drawing's wave-solder limit and the manufacturer's copper clearance requirements.
- Power and environment: Non-PoE is the listed application and the operating range is 0 °C to 70 °C. Confirm the ambient temperature and thermal rise inside the enclosure.
The table lists 16.90 mm height, 16.70 mm length and 16.00 mm width. The mechanical sheet dimensions the width at 16.15 mm; the difference is 0.15 mm and is within the sheet's tolerance class, but confirm the nominal used for the panel opening.
Dimension note: the table lists 16.00 mm width while the mechanical sheet dimensions 16.15 mm. The 0.15 mm difference is small but the nominal should be confirmed before a panel cutout is released.
Procurement and OEM Qualification
Use the full part number and the agreed drawing revision on the sample request, BOM and purchase documentation. The drawing notes IEEE 802.3 where applicable and a UL file number. Confirm the contact plating option and packaging for the actual order, then evaluate samples on the target board and complete the approved-vendor review before production release.
Engineering Verification Checklist
- Confirm the full part number, drawing revision and contact plating option.
- Review the port orientation and the host interface (with or without external magnetics).
- Verify the footprint, plated-hole sizes, pin-1 datum and panel opening.
- Check latch clearance, LED light pipes and cable bend radius.
- Confirm the application rating and the operating temperature for the enclosure.
- Resolve any drawing-versus-table dimension definition, then validate samples on the intended board.
Frequently Asked Questions
What is LPJD0012BENL used for?
The LINK-PP LPJD0012BENL is a 10/100BASE-T vertical (180°) RJ45 jack with integrated magnetics, a single port and green/yellow LEDs. Its through-hole, tab-up construction places the cable opening above the PCB and is intended for embedded boards and panel-mounted enclosures that cannot use a right-angle edge jack. The table lists Non-PoE operation at 0 °C to 70 °C.
Is LPJD0012BENL interchangeable with other vertical RJ45 jacks?
The table lists Pulse JD2-0010NL as a catalog reference, but this page does not establish a verified interchangeability approval. Compare both official drawings, the transformer ratio, center taps, LED polarity and the PCB hole pattern before substituting on an existing board.
Does LPJD0012BENL support Power over Ethernet (PoE)?
The specification lists Non-PoE application. Do not assign a PoE, PoE+ or PoE++ rating from the jack outline or the presence of center taps. A powered design needs a documented magnetic and power-path rating for the intended PoE mode.
Does LPJD0012BENL perform AutoMDX switching?
No. The assembly is a passive connector (with or without magnetics). The AutoMDX field describes use with an Ethernet PHY that supports AutoMDX; pair detection, crossover and negotiation are functions of the host PHY.
What should be checked before installing LPJD0012BENL on a PCB?
Confirm the vertical 180° orientation, the 16.90 mm height above the PCB, the 16.15 mm drawing width against the 16.00 mm table value, the panel opening, the latch clearance and the through-hole pattern. The drawing limits wave-solder tip temperature to 250 °C for 5 s.
What should be supplied when requesting LPJD0012BENL samples or a quotation?
Provide the complete part number, the drawing revision, the required contact plating (the table lists 6, 15 or 30 µin gold options) and the target quantity. Confirm sample configuration, commercial terms and delivery schedule with LINK-PP; this page does not establish stock, MOQ or a fixed lead time.
Packaging, Shipping and Global Delivery for Networking Products
Anti-static packaging, shock-resistant protection, fast order dispatch, and reliable worldwide delivery for all LINK-PP networking products.
Anti-Static Protective Packaging
Protect networking products from electrostatic discharge and handling-related damage.
Shock-Resistant Transport Protection
Protect products against physical impacts during storage and international transportation.
Fast Order Processing and Dispatch
Accelerate order handling to ensure quick warehouse deployment.
Global Logistics and International Delivery
Ship products efficiently to customers across worldwide locations.
Technical Support and Deployment Assistance
LINK-PP provides expert technical support, from product selection and compatibility verification to deployment and long-term operation.
Pre-Sales Technical Consultation
Technical consultation to help you verify compatibility and select the appropriate product for your application.
Compatibility Verification Support
Verification support to help ensure compatibility with your equipment, applications, and deployment requirements.
Deployment & Installation Assistance
Comprehensive step-by-step guidance for installation, configuration, and initial setup, ensuring accurate deployment and reliable, stable operation from the start.
Long-Term Technical Assurance
Ongoing technical support throughout the product lifecycle, delivering long-term stability for enterprise and carrier-grade networks.
Industry Standards, Compliance and Quality Assurance
LINK-PP products are manufactured under recognized quality management systems and designed to support applicable industry standards, regulatory compliance, and long-term deployment requirements, including IEEE 802.3, RoHS, REACH, ISO 9001, and ISO 14001 where applicable. 「View Quality & Compliance Center」
ISO 9001 Quality Management
Manufactured under certified quality management processes to ensure consistent product quality and production control.
IEEE 802.3 Standards Compliance
Designed in accordance with applicable networking and Ethernet standards, including IEEE specifications where relevant.
RoHS Compliance
Manufactured using materials that support restrictions on hazardous substances for global market requirements.
REACH Compliance
Material declarations and supply chain processes support applicable REACH regulatory requirements.
Product Safety Assurance
Selected products support recognized safety and reliability requirements for networking applications.
Reliability Verification Testing
Products undergo verification and quality testing to support stable operation in enterprise, telecom, and industrial environments.
Warranty and After-Sales Service
LINK-PP provides warranty coverage and after-sales support to help ensure stable operation and long-term product performance.
15-day no-reason return and refund
Free replacement for dead-on-arrival (DOA) or defective items within the initial period
Free repair services for manufacturing defects throughout the warranty period
Warranty exclusions and conditions apply
Keyword:
Download
Product Drawing
3D Model
Q&A
What certifications does LINK-PP have?
LINK-PP holds ISO9001:2015 international quality system certification, ROHS environmental certification, UL, Reach, and ISO14001:2015 environmental certification.
Can i get free samples before i make big quantity purchase?
Yes, join us as a business account, we could offer free samples to you for evaluation. Or you could return or pay after you test the samples.
Recommend
-
Nav Menu
-
About LINK-PP
-
All Products
-
Applications







































