HOT CROSS-REFERENCE SEARCHES All Products
HR911105A Cisco GLC-LH-SMD Pulse J1011F21PNL LPJG0926HENL TE 2170704-1 SFP-10G-SR
POPULAR CATEGORIES
Matched Parts (Real-time ES) Use ↑ ↓ to select, Enter to open
+
  • LPJ0011BBNL印字.jpg
  • LPJ0011BBNL金针(1713757752171).jpg
  • LPJ0011BBNL底部(1713757752153).jpg
  • LPJ0011BBNL背部.jpg

LPJ0011BBNL RJ45 Jack with Magnetics 10/100 Base-T Tab Down Single Port Green/Yellow Led

P/N:

LPJ0011BBNL

Manufacturer:

LINK-PP

Compatible Brand:

LINK-PP

Compatible P/N:

LPJ0011BBNL

  • Compatible Brands: LINK-PP
  • Number of Ports: 1X1
  • Speed: 10Base-T,100Base-TX
  • PoE: Non-PoE
  • Latch: Down
  • Mounting Type: THT
  • LED Option: Green / Yellow
  • Shield EMI Tabs: NO
  • Temperature: 0℃ to 70℃
  • P/N: LPJ0011BBNL
  • Manufacturer: LINK-PP
  • Compatible Brand: LINK-PP
  • Compatible P/N: LPJ0011BBNL

Packaging Details:

N.W/pCS:

0.007kg

Package:

Tray

SPQ:

50pcs

Qty/carton:

1200pcs

Carton size:

32*30*31cm

G.W/carton:

8.5kg

Product Specifications

LINK-PP Part Number LPJ0011BBNL Connector Type Jack
Part Status Active Mounting Type Through Hole
Number of Positions/Contacts 8p8c (RJ45, Ethernet) Application-Lan Ethernet(Non-PoE)
Number of Ports 1x1 Port Speed 10/100 Base-T
Latch Down Cores per Port 4
Orientation 90° Angle (Right) PCB Mount Angle SIDE ENTRY
Shield EMI Tabs Without LED Option Green/Yellow
PCB FR4 PCB Retaining Post T POST
Package Height (Inches/mm) 0.528/13.40 Package Length (Inches/mm) 0.839/21.30
Package Width (Inches/mm) 0.626/15.90 Temperature 0℃ TO 70℃
Bst Circuit Yes AutomDX YES
Diodes No Contact Mating Area Plating GOLD 6u"/15u"/30u"
Turns Ratio RX/TX 1CT:1CT Configuration RX/TX T,C

Product Engineering Overview

The LINK-PP LPJ0011BBNL is a 10/100BASE-T RJ45 jack with integrated magnetics in a single-port, tab-down through-hole package. It combines the 8P8C mating interface, the isolation transformers and the 75 Ω common-mode termination used in a 10/100 Ethernet interface.

The connector is listed for Non-PoE applications with green/yellow status LEDs and an operating range of 0 °C to 70 °C. It is intended for host boards that accept a right-angle, side-entry THT jack. Before layout release, check the board cutout, panel opening, LED light-pipe alignment and the magjack land pattern against the product drawing.

Interface: 10/100BASE-T
Power application: Non-PoE
Mounting: Through-hole, right-angle
Ports / latch / LEDs: 1x1 / Tab Down / Green-Yellow
Operating temperature: 0 °C to 70 °C
Drawing revision: Rev A (LP08121220)

Design Positioning and Qualification

This page does not establish a verified cross-reference to another manufacturer's 8-pin 10/100 jack. Other LINK-PP catalog entries that mention alternate part numbers are separate product pages; a shared pin count, package style or LED colour is not evidence of electrical or mechanical interchangeability. Qualify the actual host board, including the transformer ratio, center taps, LED circuit and footprint, rather than relying on a presumed standard outline.

Electrical and Mechanical Integration

The drawing lists a 1CT:1CT transmit and receive ratio, 350 µH minimum open-circuit inductance at 100 kHz with 0.1 V and 8 mA DC bias, and 1500 Vrms hipot. These are component characteristics; the host PHY, termination and EMC network still determine whether the port meets the target interface specification.

  • PHY and magnetics: Compare the TX/RX pairs, center taps and 75 Ω common-mode termination with the PHY reference circuit. The jack is a passive component and does not implement link negotiation or AutoMDX.
  • PCB and soldering: Use the suggested land pattern and keep the plated-hole drill sizes, 1.27 mm pin pitch, 8.89 mm row spacing and side-entry orientation consistent with the mechanical sheet. The drawing limits wave-solder tip temperature to 265 °C for 5 s maximum.
  • Panel and LEDs: Green is the left LED and yellow the right LED. The LED forward voltage is 1.8-2.6 V at 20 mA, so size the series resistors from the actual driver supply and check light-pipe alignment with the front panel.
  • Power and environment: Non-PoE is the listed application and the operating range is 0 °C to 70 °C. Verify the ambient temperature and the thermal rise inside the enclosure; the component rating alone does not qualify the complete equipment.

Dimension note: the specification table lists 0.528 in / 13.40 mm height, 0.839 in / 21.30 mm length and 0.626 in / 15.90 mm width. The mechanical views are dimensioned 13.30 mm high, 21.25 mm long and 15.93 mm wide. The differences are small but the dimension definitions are not identical; confirm the controlling values with the drawing before committing an enclosure or panel cutout.

Procurement and OEM Qualification

Use the full part number and the agreed drawing revision on the sample request, BOM and purchase documentation. The drawing notes IEEE 802.3 compatibility and UL file E484635, and specifies a PBT +30% GF UL94V-0 housing, phosphor-bronze contacts and a SUS 201 shield. Confirm the contact plating option and the packaging for the actual order, then evaluate samples on the target board and complete the approved-vendor review before production release.

Engineering Verification Checklist

  1. Confirm the full part number, drawing revision (Rev A, LP08121220) and contact plating option.
  2. Review the TX/RX pairs, center taps and 75 Ω termination against the host PHY reference design.
  3. Verify the right-angle side-entry footprint, plated-hole sizes, 1.27 mm pin pitch, 8.89 mm row spacing and pin-1 datum.
  4. Check the panel opening, latch clearance and green/yellow LED light-pipe alignment.
  5. Confirm the Non-PoE application and the 0 °C to 70 °C operating limit for the enclosure.
  6. Resolve the table-versus-drawing dimension definitions, then validate samples on the intended board.

Frequently Asked Questions

What is LPJ0011BBNL used for?

It is a 10/100BASE-T single-port RJ45 jack with integrated magnetics, a tab-down latch and through-hole mounting. The drawing names SOHO gateways, LAN-on-motherboard ports and switches as target applications for a right-angle jack with status LEDs. The catalog lists the component for 0 °C to 70 °C operation and Non-PoE applications.

Is LPJ0011BBNL interchangeable with other 8-pin 10/100 RJ45 jacks?

Do not assume interchangeability. This page does not establish a verified cross-reference for any third-party part number, and other LINK-PP catalog entries that mention alternate part numbers are separate product pages. Compare the official drawings, transformer turns ratio, center-tap arrangement, LED polarity, shield and PCB hole pattern before substituting on an existing board.

Does LPJ0011BBNL support Power over Ethernet (PoE)?

The specification lists Non-PoE application. Do not assign a PoE, PoE+ or PoE++ rating from the jack outline or the presence of center taps. A powered design needs a documented magnetic and power-path rating for the intended PoE mode, plus verification of the complete PSE or PD circuit.

Does LPJ0011BBNL perform AutoMDX switching?

No. The assembly is a passive magnetic jack. The AutoMDX field describes use with an Ethernet PHY that supports AutoMDX; pair detection, crossover and negotiation are functions of the host PHY, not of the connector.

What should be checked before installing LPJ0011BBNL on a PCB?

Confirm the right-angle side-entry orientation, the 8P8C opening and latch clearance, the LED positions (green left, yellow right) and the plated through-hole pattern from the mechanical sheet. The drawing gives a suggested layout with a 1.27 mm pin pitch, 8.89 mm row spacing, 8 × 0.90 mm holes, 2 × 1.70 mm holes, 2 × 3.20 mm locating holes and 4 × 1.02 mm holes, and limits wave-solder tip temperature to 265 °C for 5 s. The table lists 13.40 mm height, 21.30 mm length and 15.90 mm width, while the mechanical views show 13.30 mm, 21.25 mm and 15.93 mm; confirm the applicable dimension definition before fixing the enclosure.

What should be supplied when requesting LPJ0011BBNL samples or a quotation?

Provide the complete part number, the drawing revision, the required contact plating (the table lists 6, 15 or 30 µin gold options; the drawing specifies 6 µin minimum in the contact area) and the target quantity. Confirm sample configuration, commercial terms and delivery schedule with LINK-PP; this page does not establish stock, MOQ or a fixed lead time.

Packaging, Shipping and Global Delivery for Networking Products

Anti-static packaging, shock-resistant protection, fast order dispatch, and reliable worldwide delivery for all LINK-PP networking products.

Anti-Static Protective Packaging

Anti-Static Protective Packaging

Protect networking products from electrostatic discharge and handling-related damage.

Shock-Resistant Transport Protection

Shock-Resistant Transport Protection

Protect products against physical impacts during storage and international transportation.

Fast Order Processing and Dispatch

Fast Order Processing and Dispatch

Accelerate order handling to ensure quick warehouse deployment.

Global Logistics and International Delivery

Global Logistics and International Delivery

Ship products efficiently to customers across worldwide locations.

Technical Support and Deployment Assistance

LINK-PP provides expert technical support, from product selection and compatibility verification to deployment and long-term operation.

Pre-Sales Technical Consultation

Pre-Sales Technical Consultation

Technical consultation to help you verify compatibility and select the appropriate product for your application.

Compatibility Verification Support

Compatibility Verification Support

Verification support to help ensure compatibility with your equipment, applications, and deployment requirements.

Deployment & Installation Assistance

Deployment & Installation Assistance

Comprehensive step-by-step guidance for installation, configuration, and initial setup, ensuring accurate deployment and reliable, stable operation from the start.

Long-Term Technical Assurance

Long-Term Technical Assurance

Ongoing technical support throughout the product lifecycle, delivering long-term stability for enterprise and carrier-grade networks.

Industry Standards, Compliance and Quality Assurance

LINK-PP products are manufactured under recognized quality management systems and designed to support applicable industry standards, regulatory compliance, and long-term deployment requirements, including IEEE 802.3, RoHS, REACH, ISO 9001, and ISO 14001 where applicable. 「View Quality & Compliance Center」

ISO 9001 Quality Management System Certification

ISO 9001 Quality Management

Manufactured under certified quality management processes to ensure consistent product quality and production control.

IEEE 802.3 Ethernet Standard Compliance

IEEE 802.3 Standards Compliance

Designed in accordance with applicable networking and Ethernet standards, including IEEE specifications where relevant.

RoHS Compliance

RoHS Compliance

Manufactured using materials that support restrictions on hazardous substances for global market requirements.

REACH Compliance

REACH Compliance

Material declarations and supply chain processes support applicable REACH regulatory requirements.

Product Safety Assurance

Product Safety Assurance

Selected products support recognized safety and reliability requirements for networking applications.

Reliability Verification Testing

Reliability Verification Testing

Products undergo verification and quality testing to support stable operation in enterprise, telecom, and industrial environments.

Warranty and After-Sales Service

LINK-PP provides warranty coverage and after-sales support to help ensure stable operation and long-term product performance.

15 days

15-day no-reason return and refund

Free maintenance or replacement

Free replacement for dead-on-arrival (DOA) or defective items within the initial period

Free maintenance

Free repair services for manufacturing defects throughout the warranty period

Limitations

Warranty exclusions and conditions apply

Q&A

图片名称

What certifications does LINK-PP have?


图片名称

LINK-PP holds ISO9001:2015 international quality system certification, ROHS environmental certification, UL, Reach, and ISO14001:2015 environmental certification.

图片名称

Can i get free samples before i make big quantity purchase?


图片名称

Yes, join us as a business account, we could offer free samples to you for evaluation. Or you could return or pay after you test the samples.