Cisco GLC-SX-MMD Compatible Industrial 1000BASE-SX SFP Module with DOM
P/N:
LS-MM851G-S5I
Manufacturer:
LINK-PP
Compatible Brand:
Cisco
Compatible P/N:
GLC-SX-MMD
- Compatible Brands: Cisco
- Form Factor: SFP
- Data Rate: 1G
- Distance: ≤550m
- Type: Multimode
- Connector: Duplex LC
- Wavelength: 850nm
- P/N: LS-MM851G-S5I
- Manufacture: LINK-PP
- Compatible Brand: Cisco
- Compatible P/N: GLC-SX-MMD
Before Purchasing a GLC-SX-MMD Compatible Module
To ensure drop-in compatibility and avoid deployment delays, network planners should verify the following Layer-1 prerequisites:
- Verify that your existing fiber plant is Multimode (OM1/OM2/OM3/OM4), not Single-Mode.
- Ensure both endpoints of the link are configured for Gigabit Ethernet (1.25Gbps) speed without auto-negotiation mismatches.
- Confirm that standard LC duplex connectors are installed on your patch panel.
- Check switch platform requirements (ensure the target chassis accepts third-party SFP form factors).
- Evaluate environmental conditions to ensure enclosure temperatures fall within the -40°C to 85°C operating range.
Cisco GLC-SX-MMD Compatible SFP Specifications
The Link-PP LS-MM851G-S5I is a high-performance, cost-effective Cisco compatible GLC-SX-MMD SFP transceiver, engineered for 1.25Gbps Gigabit Ethernet links. Supporting a transmission distance of up to 550m over Multimode Fiber (MMF), this module is the ideal 1000Base-SX solution for businesses seeking a reliable alternative to original Cisco infrastructure without compromising on optical performance or network integrity.
| LINK-PP Part Number | LS-MM851G-S5I | Cisco Compatible | GLC-SX-MMD |
|---|---|---|---|
| Form Factor | SFP | Max Data Rate | 1.25Gbps |
| Wavelength | 850nm | Max Cable Distance | 550m over OM2 MMF |
| Connector | Duplex LC | Optical Components | VCSEL 850nm |
| Media Type | MMF (Multimode) | DOM Support | Yes (SFF-8472) |
| TX Power | -9.0 to 0 dBm | RX Power | -20.0 to -1.0 dBm |
| Receiver Sensitivity | -18.0 dBm | Receiver Overload | -1.0 dBm |
| Operating Temperature | -40°C to 85°C (Industrial) | Protocols & Standards | IEEE 802.3z, SFF-8472, FC-PI, SFP MSA (INF-8074i) |
Optical Performance Specifications
Link reliability depends entirely on the optical budget. Validate these specifications against your OTDR trace reports to prevent bit errors caused by excessive attenuation.
| Parameter | Specification Value |
|---|---|
| Transmit Power (Tx) | -9.5 dBm to -4.0 dBm |
| Receiver Sensitivity (Rx) | -17.0 dBm |
| Overload Power | 0.0 dBm |
| Optical Link Budget | 7.5 dB |
Supported Fiber Types & Maximum Distances
| Fiber Type | Core / Cladding Size | Maximum Supported Distance |
|---|---|---|
| OM1 | 62.5/125µm | 220 meters |
| OM2 | 50/125µm | 550 meters |
| OM3 | 50/125µm | 550 meters |
| OM4 | 50/125µm | 550 meters |
Industrial vs Commercial Optical Transceivers
When selecting optics for edge networks, relying on commercial-grade OEM parts can limit deployment flexibility. Here is why industrial-grade modules are critical for Operational Technology (OT) networks:
| Deployment Feature | Industrial SFP (This Module) | Commercial SFP (OEM Standard) |
|---|---|---|
| Operating Temperature | -40°C to 85°C | 0°C to 70°C |
| Outdoor NEMA Cabinets | Supported natively | Not Recommended |
| Industrial Ethernet Switch | Recommended | Limited capabilities |
| SCADA / Factory Floor | Recommended | Risky (Thermal drift vulnerability) |
Validated Cisco Compatibility Matrix
| Platform / Switch Series | Validation Status | Notes |
|---|---|---|
| Catalyst 2960-X / 3850 / 9300 Series | Validated | Verified in native SFP and Network Modules (NM) |
| Nexus 3000 / 9000 Series | Validated | SFP+ ports natively backward compatible to 1G |
| Cisco Industrial Ethernet (IE3000/IE4000) | Validated | Utilizes full industrial temperature range |
Engineering Validation: Cisco IOS Recognition
To ensure zero procurement risk, modules are validated to populate EEPROM data correctly within Cisco IOS platforms. A genuine recognition trace will output the expected PID:
Switch# show inventory
NAME: "GigabitEthernet1/0/1", DESCR: "1000BaseSX SFP"
PID: GLC-SX-MMD , VID: V01 , SN: F2106000026
How to Verify Link Health Using DOM Diagnostics
Network administrators can verify the module's health and optical path integrity directly from the CLI. This prevents unnecessary physical replacements by diagnosing optical loss directly:
Switch# show interfaces transceiver detail
ITU Channel not available (Wavelength not available),
Transceiver is internally calibrated.
If device is externally calibrated, only calibrated values are printed.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
NA or N/A: not applicable, Tx: transmit, Rx: receive.
mA: milliamperes, dBm: decibels (milliwatts).
Optical Optical
Temperature Voltage Tx Power Rx Power Tx Bias
Port (Celsius) (Volts) (dBm) (dBm) Current (mA)
--------- ----------- ------- -------- -------- ------------
Gi1/0/1 38.5 3.29 -5.2 -8.4 6.1
Diagnosis: Compare the Rx Power (-8.4 dBm in this example) against the module's Receiver Sensitivity specification (-17.0 dBm). Unexpectedly low values (e.g., approaching -16 dBm) may indicate excessive fiber attenuation, connector contamination, or macro-bending.
Frequently Asked Questions
What is a GLC-SX-MMD?
The GLC-SX-MMD is a standard Cisco-branded SFP transceiver that operates over Gigabit Ethernet (1000BASE-SX) using an 850nm wavelength. The "D" at the end of the part number indicates that the module supports Digital Optical Monitoring (DOM).
What is the difference between GLC-SX-MM and GLC-SX-MMD?
The primary difference is diagnostic capabilities. The legacy GLC-SX-MM does not support SFF-8472 DOM, whereas the newer GLC-SX-MMD natively supports real-time metrics.
Can this 1G module work in a 10G SFP+ port?
Yes, many Cisco SFP+ ports are backward compatible. However, the link will only operate at 1.25Gbps, and the remote device must also run 1G 1000BASE-SX optics.
What is the maximum transmission distance?
The maximum distance is 550 meters when using 50/125µm multimode fiber (OM2, OM3, or OM4). With legacy 62.5/125µm fiber (OM1), the distance is limited to 220 meters.
Packaging, Shipping and Global Delivery for Networking Products
Anti-static packaging, shock-resistant protection, fast order dispatch, and reliable worldwide delivery for all LINK-PP networking products.
Anti-Static Protective Packaging
Protect networking products from electrostatic discharge and handling-related damage.
Shock-Resistant Transport Protection
Protect products against physical impacts during storage and international transportation.
Fast Order Processing and Dispatch
Accelerate order handling to ensure quick warehouse deployment.
Global Logistics and International Delivery
Ship products efficiently to customers across worldwide locations.
1G SFP Technical Support and Deployment Assistance
LINK-PP provides expert technical support, from product selection and compatibility verification to deployment and long-term operation.
Pre-Sales Technical Consultation
Technical consultation to help you verify GLC-SX-MMD compatibility and select the appropriate product for your application.
Compatibility Verification Support
Verification support to help ensure compatibility with your equipment, applications, and deployment requirements.
Deployment & Installation Assistance
Comprehensive step-by-step guidance for installation, configuration, and initial setup, ensuring accurate deployment and reliable, stable operation from the start.
Long-Term Technical Assurance
Ongoing technical support throughout the product lifecycle, delivering long-term stability for enterprise and carrier-grade networks.
Industry Standards, Compliance and Quality Assurance
LINK-PP products are manufactured under recognized quality management systems and designed to support applicable industry standards, regulatory compliance, and long-term deployment requirements, including IEEE 802.3, RoHS, REACH, ISO 9001, and ISO 14001 where applicable. 「View Quality & Compliance Center」
ISO 9001 Quality Management
Manufactured under certified quality management processes to ensure consistent product quality and production control.
IEEE 802.3 Standards Compliance
Designed in accordance with applicable networking and Ethernet standards, including IEEE specifications where relevant.
RoHS Compliance
Manufactured using materials that support restrictions on hazardous substances for global market requirements.
REACH Compliance
Material declarations and supply chain processes support applicable REACH regulatory requirements.
Product Safety Assurance
Selected products support recognized safety and reliability requirements for networking applications.
Reliability Verification Testing
Products undergo verification and quality testing to support stable operation in enterprise, telecom, and industrial environments.
1G SFP Warranty and After-Sales Service
LINK-PP provides warranty coverage and after-sales support to help ensure stable operation and long-term product performance.
15-day no-reason return and refund
Free replacement for dead-on-arrival (DOA) or defective items within the initial period
Free repair services for manufacturing defects throughout the warranty period
Warranty exclusions and conditions apply
Keyword:
SFP Download
Product Drawing
Cisco Compatible 1G GLC-SX-MMD FAQ
Recommend
-
Nav Menu
-
About LINK-PP
-
All Products
-
Applications







































