HOT CROSS-REFERENCE SEARCHES All Products
HR911105A Cisco GLC-LH-SMD Pulse J1011F21PNL LPJG0926HENL TE 2170704-1 SFP-10G-SR
POPULAR CATEGORIES
Matched Parts (Real-time ES) Use ↑ ↓ to select, Enter to open
+
  • LS-SM3110-10C.jpg
  • LS-SM3110-10C-1.jpg
  • LS-SM3110-10C-2.jpg
  • LS-SM3110-10C-3.jpg
  • LS-SM3110-10C-4.jpg

Cisco Compatible 10G SFP+ (1310nm,10km,LC SMF,DOM,Compatible With SFP-10G-LR)

P/N:

LS-SM3110-10C

Manufacturer:

LINK-PP

Classification:

Compatible Brand:

Cisco

Compatible P/N:

SFP-10G-LR

  • Compatible Brands: Cisco
  • Form Factor: SFP+
  • Data Rate: 10G
  • Distance: ≤10km
  • Type: Single Mode
  • Connector: Duplex LC
  • Model: LR
  • Wavelength: 1310nm
  • P/N: LS-SM3110-10C
  • Manufacture: LINK-PP
  • Compatible Brand: Cisco
  • Compatible P/N: SFP-10G-LR

Cisco SFP-10G-LR Compatible LINK-PP LS-SM3110-10C 10GBASE-LR SFP+ Transceiver Module (SMF, 1310nm, 10km, LC, DOM)

The LINK-PP LS-SM3110-10C is a Cisco SFP-10G-LR compatible 10GBASE-LR SFP+ optical transceiver for 10 Gigabit Ethernet connections over single-mode fiber. It operates at a nominal wavelength of 1310 nm and supports distances up to 10 km over single-mode fiber, subject to the link's optical loss and operating conditions. The module has a duplex LC interface, a DFB transmitter, a PIN receiver, and digital optical monitoring (DOM).

For enterprise uplinks, campus backbones, and data center connections, the LS-SM3110-10C provides a LINK-PP alternative to the Cisco SFP-10G-LR. Before ordering, confirm the exact Cisco host, port or network module, software version, fiber route, and remote-end interface. A Cisco part-number cross-reference is a starting point for selection; compatibility with a particular deployment should be reviewed separately.

  • 10GBASE-LR: 10.3125 Gbps Ethernet line rate with an up-to-10 km single-mode optical interface.
  • 1310 nm optical engine: DFB laser transmitter and PIN photodiode receiver with duplex LC connectivity.
  • Digital optical monitoring: Temperature, supply voltage, laser bias current, TX power, and RX power monitoring, subject to host support.
  • Hot-pluggable SFP+: Install or replace the module according to the host manufacturer's procedures without powering down the host.
  • Commercial operating case temperature: 0 to 70°C for LS-SM3110-10C.

Product Specifications

LINK-PP Part Number LS-SM3110-10C Cisco Compatible Part Number SFP-10G-LR
Part Status Active Form Factor SFP+
Maximum Data Rate Up to 10.7 Gbps 10GBASE-LR Line Rate 10.3125 Gbps
Nominal Wavelength 1310 nm Maximum Reach 10 km over SMF
Connector Duplex LC Fiber Media Single-mode fiber (SMF)
Transmitter DFB laser Receiver PIN photodiode
Average TX Optical Power -6.5 to -0.5 dBm Receiver Sensitivity -14.4 dBm maximum*
Receiver Overload +0.5 dBm* DOM RX Power Monitoring Range -20 to -1 dBm
Operating Case Temperature 0 to 70°C Digital Diagnostic Monitoring Supported
Interface 10GBASE-LR Management and Form Factor SFF-8472 and SFP+ MSA

Specification notes: Values are based on the LS-SM3110-10C datasheet, Rev. 1.0, September 2016. Confirm the current revision and ordering configuration before procurement. *Receiver sensitivity and overload use the datasheet's specified test condition: PRBS 231-1 at 10,312 Mbps and BER ≤ 1 × 10-12. The DOM RX power range is a diagnostic measurement range, not the receiver sensitivity or overload limit.

Key Benefits of the Cisco SFP-10G-LR Compatible Transceiver

  • Single-mode 10G uplinks: The 1310 nm interface supports 10GBASE-LR links up to the specified 10 km reach when the complete optical path meets the required conditions.
  • Link diagnostics: DOM measurements can help operators establish a baseline and investigate changes in optical power, temperature, voltage, or bias current.
  • Serviceable form factor: The SFP+ module can be replaced without turning off the host, following platform-specific handling procedures. The affected link will be interrupted during replacement.
  • Commercial-temperature option: The 10C suffix identifies the 0 to 70°C case-temperature version in the referenced datasheet. Check the required temperature at the specified measurement point.
  • Secondary-source evaluation: A Cisco part-number reference helps procurement teams identify a candidate, while host and link checks determine suitability for the intended configuration.

10GBASE-LR Optical Link Budget and 1310nm DFB Architecture

The LS-SM3110-10C combines a 1310 nm DFB transmitter with a PIN receiver and transimpedance amplifier for single-mode fiber links. The nominal 10 km reach is a product reach specification, not a substitute for checking the actual fiber route, connectors, splices, and operating margins.

How to Calculate the Available Optical Power Difference

For an illustrative calculation using the transmitter and receiver limits in the referenced LINK-PP datasheet, subtract the receiver sensitivity value from the minimum average transmitter power:

Parameter Value Meaning
Minimum average TX power -6.5 dBm Transmitter output launched into SMF, per datasheet
Receiver sensitivity -14.4 dBm Specified sensitivity limit under the datasheet test conditions
Calculated difference 7.9 dB -6.5 - (-14.4); illustrative transmitter-to-receiver power difference

The 7.9 dB figure is calculated from the two LINK-PP limits above; it is not a measured link margin or a guarantee for every 10 km route. When the remote module is a different product, use the transmitting module's minimum output and the receiving module's sensitivity for each direction. Account for fiber attenuation, connectors, splices, patch panels, measurement uncertainty, and the margin required by the network design.

Also check the high-power condition separately: compare the highest relevant transmitter output after the minimum expected path loss with the receiving module's overload specification. An attenuator should be selected only if the receiver and link calculations or measurements require one. Do not infer that every short 10GBASE-LR link needs an attenuator.

Digital Optical Monitoring and Link Diagnostics

The module's digital diagnostics provide access to temperature, supply voltage, laser bias current, transmitted optical power, and received optical power through its management interface. The host must support and expose the relevant fields. Record a baseline after installation and compare later readings with the module's applicable warning and alarm thresholds.

The datasheet lists an RX power monitoring range of -20 to -1 dBm with stated measurement accuracy. A displayed value is a diagnostic reading; it is not a replacement for the receiver sensitivity or overload limits. If a reading is close to a limit or does not match observed link behavior, verify the path using an appropriate calibrated optical power meter and the applicable datasheet.

Cisco Switch Interoperability and EEPROM Coding

LS-SM3110-10C is offered by LINK-PP as a Cisco SFP-10G-LR compatible alternative. The host reads information from the module, and recognition may depend on the exact hardware, port, software release, and module configuration. Identifying the module is one step; the link also needs a supported speed, compatible optics at the other end, and a suitable fiber path.

Use Cisco's Optics-to-Device Compatibility Matrix and the equipment documentation to check the Cisco original optic and port conditions. The Cisco matrix does not establish Cisco support for a third-party LINK-PP module. For LINK-PP product selection, provide the exact host and software details and request available compatibility or test information for that configuration.

For further guidance, see the Cisco SFP compatibility and LINK-PP cross-reference guide. Do not assume that every Catalyst, Nexus, or ASR port has the same transceiver support or that an unsupported-transceiver command is applicable to every platform.

Applications for the LS-SM3110-10C 10GBASE-LR Module

  • Enterprise core and aggregation: 10GbE uplinks between compatible switches or routers over single-mode fiber.
  • Campus and inter-building links: Connections over suitable single-mode cabling within the module's reach and the complete link budget.
  • Data center connections: 10GBASE-LR links between compatible network ports over single-mode fiber, including links between rooms or sites when the path meets optical requirements.

The datasheet states a maximum bit rate up to 10.7 Gbps and identifies 10GBASE-LR and 10GBASE-LW applications. A maximum bit rate alone does not confirm OTU2, CPRI, or eCPRI support for a particular host and line rate. For these applications, request the applicable product specification and validate the intended configuration.

How to Select and Verify LS-SM3110-10C vs. Cisco SFP-10G-LR

  1. Identify the host: Record the full Cisco device PID, SFP+ port or network module, and software release. Check the original Cisco optic against the current Cisco matrix and port documentation.
  2. Specify the LINK-PP configuration: Provide the LINK-PP part number and host details when requesting coding and compatibility information. Ask for a test record for the exact configuration if one is required.
  3. Check the fiber path: Use an appropriate single-mode fiber route with compatible duplex LC connections. Confirm polarity, connector cleanliness, actual route length, and all patch panels and splices.
  4. Check both optical directions: Match the 10GBASE-LR interface and line rate at the remote end. Calculate or measure receive power using the actual transmitting and receiving specifications.
  5. Verify the environment: Confirm the 0 to 70°C case-temperature range, host power allowance, and airflow. For industrial-temperature requirements, evaluate the exact alternative separately.
  6. Record the baseline: After installation, check inventory, link state, optical readings where available, and interface error counters. Use commands and procedures documented for the specific platform and software.

For a compatibility review or quotation, contact the LINK-PP team with the device model, port, software version, required quantity, fiber type, and link distance.

Part Number and Temperature Selection

Part number Description in referenced datasheet Selection note
LS-SM3110-10C 1310 nm, 10 km, duplex LC, 0 to 70°C, with DDM Commercial case-temperature version. Confirm host, coding, and link conditions.
LS-SM3110-10I 1310 nm, 10 km, duplex LC, -40 to 85°C, with DDM Industrial-temperature version. Confirm the current datasheet, ordering configuration, and compatibility for the intended host.

Both entries are listed in the referenced LS-SM3110-10C datasheet's ordering information. Temperature grade alone does not establish interchangeability or device-specific qualification.

Frequently Asked Questions

Is LS-SM3110-10C compatible with Cisco SFP-10G-LR?

LINK-PP lists LS-SM3110-10C as a Cisco SFP-10G-LR compatible alternative. Confirm the exact Cisco host, port, software version, and requested module configuration. Cisco's support listing for its original module is separate from the evaluation of a third-party transceiver.

What fiber and distance does LS-SM3110-10C support?

The referenced datasheet specifies up to 10 km over single-mode fiber with a duplex LC interface. Verify the actual route length and optical loss, as well as the far-end interface and receiver power limits.

Can a 10GBASE-LR module connect directly to a 10GBASE-SR module?

Do not select LR and SR as a direct pair. LR uses a 1310 nm single-mode interface, while SR is an 850 nm multimode interface. Select compatible optical interfaces and fiber for the complete link.

Does LS-SM3110-10C support DOM?

Yes. The datasheet lists digital diagnostic monitoring for optical power, temperature, supply voltage, and laser bias current. Which readings are displayed depends on the host and software.

What does the 7.9 dB optical power difference mean?

It is calculated from the minimum transmitter output of -6.5 dBm and the receiver sensitivity of -14.4 dBm in the referenced datasheet. It is not a measured installation margin; include actual path losses, uncertainty, and the required engineering margin.

Can the module be used for CPRI, eCPRI, or OTU2?

The referenced datasheet states a maximum rate up to 10.7 Gbps, but that alone does not establish support for every protocol, host, or line rate. Contact LINK-PP with the exact application and equipment to obtain the applicable specification and validation information.

Does installing a third-party transceiver affect Cisco support or warranty?

Cisco states that its optics matrix does not support third-party optics. Warranty and service terms depend on the applicable contract, the issue, and local law. Review the current Cisco policy and your agreement, and consult the relevant support provider about the specific deployment.

Can I replace the module while the switch is powered on?

The module uses a hot-pluggable SFP+ form factor. Follow the host manufacturer's procedures and operational change controls. Removing a module interrupts the affected link even when the host remains powered on.

Technical Support and Deployment Assistance

For product selection, a datasheet request, or a compatibility review, share the exact Cisco device and port, software release, existing optic, remote-end module, fiber type, link distance, temperature requirements, and quantity with LINK-PP. Available test documentation and suitable ordering options can then be reviewed for the intended configuration.

Reference: LINK-PP LS-SM3110-10C datasheet, Rev. 1.0 and Cisco 10GBASE SFP+ Modules Data Sheet. Cisco part numbers are referenced for comparison. LINK-PP products are independently manufactured and are not Cisco original products.

Packaging, Shipping and Global Delivery for Networking Products

Anti-static packaging, shock-resistant protection, fast order dispatch, and reliable worldwide delivery for all LINK-PP networking products.

Anti-Static Protective Packaging

Anti-Static Protective Packaging

Protect networking products from electrostatic discharge and handling-related damage.

Shock-Resistant Transport Protection

Shock-Resistant Transport Protection

Protect products against physical impacts during storage and international transportation.

Fast Order Processing and Dispatch

Fast Order Processing and Dispatch

Accelerate order handling to ensure quick warehouse deployment.

Global Logistics and International Delivery

Global Logistics and International Delivery

Ship products efficiently to customers across worldwide locations.

10G SFP+ Technical Support and Deployment Assistance

LINK-PP provides expert technical support, from product selection and compatibility verification to deployment and long-term operation.

Pre-Sales Technical Consultation

Pre-Sales Technical Consultation

Technical consultation to help you verify SFP-10G-LR compatibility and select the appropriate product for your application.

Compatibility Verification Support

Compatibility Verification Support

Verification support to help ensure compatibility with your equipment, applications, and deployment requirements.

Deployment & Installation Assistance

Deployment & Installation Assistance

Comprehensive step-by-step guidance for installation, configuration, and initial setup, ensuring accurate deployment and reliable, stable operation from the start.

Long-Term Technical Assurance

Long-Term Technical Assurance

Ongoing technical support throughout the product lifecycle, delivering long-term stability for enterprise and carrier-grade networks.

Industry Standards, Compliance and Quality Assurance

LINK-PP products are manufactured under recognized quality management systems and designed to support applicable industry standards, regulatory compliance, and long-term deployment requirements, including IEEE 802.3, RoHS, REACH, ISO 9001, and ISO 14001 where applicable. 「View Quality & Compliance Center」

ISO 9001 Quality Management System Certification

ISO 9001 Quality Management

Manufactured under certified quality management processes to ensure consistent product quality and production control.

IEEE 802.3 Ethernet Standard Compliance

IEEE 802.3 Standards Compliance

Designed in accordance with applicable networking and Ethernet standards, including IEEE specifications where relevant.

RoHS Compliance

RoHS Compliance

Manufactured using materials that support restrictions on hazardous substances for global market requirements.

REACH Compliance

REACH Compliance

Material declarations and supply chain processes support applicable REACH regulatory requirements.

Product Safety Assurance

Product Safety Assurance

Selected products support recognized safety and reliability requirements for networking applications.

Reliability Verification Testing

Reliability Verification Testing

Products undergo verification and quality testing to support stable operation in enterprise, telecom, and industrial environments.

10G SFP+ Warranty and After-Sales Service

LINK-PP provides warranty coverage and after-sales support to help ensure stable operation and long-term product performance.

15 days

15-day no-reason return and refund

Free maintenance or replacement

Free replacement for dead-on-arrival (DOA) or defective items within the initial period

Free maintenance

Free repair services for manufacturing defects throughout the warranty period

Limitations

Warranty exclusions and conditions apply

SFP Download