Ciena CWDM-SFP10G-1610 Compatible LS-CW6110-20C SFP+ 10G CWDM 1610nm 20km DOM Duplex LC/UPC SMF Optical Transceiver Module
P/N:
LS-CW6110-20C
Manufacturer:
LINK-PP
Compatible Brand:
Ciena
Compatible P/N:
CWDM-SFP10G-1610
- Compatible Brands: Ciena
- Form Factor: SFP+
- Data Rate: 10G
- Distance: ≤20km
- Type: Single Mode
- Connector: Duplex LC
- Wavelength: 1350nm-1610nm
- P/N: LS-CW6110-20C
- Manufacture: LINK-PP
- Compatible Brand: Ciena
- Compatible P/N: CWDM-SFP10G-1610
Product Specifications
| LINK-PP Part Number | LS-CW6110-20C | Ciena Part Number Equivalent | CWDM-SFP10G-1610 |
| Form Factor | SFP+ | Part Status | Active |
| Max Data Rate | 10Gbps | Optical Wavelength | 1610nm (CWDM) |
| Max Transmission Distance | 20km | Optical Media | Single Mode Fiber (SMF, G.652) |
| Optical Connector | Duplex LC/UPC | Transmitter Type | DFB CWDM |
| Receiver Type | PIN Photodiode | DOM Support | Yes (SFF-8472) |
| TX Optical Power | -1 to +5 dBm | RX Optical Power Range | -23 to -6 dBm |
| Receiver Sensitivity | -16 dBm | Receiver Overload | 0 dBm |
| Operating Temperature | 0°C to +70°C (Commercial) | Standard Compliance | SFP+ MSA, SFF-8431, SFF-8472, Class 1 Laser |
| Protocols Supported | 10G Ethernet, CPRI, eCPRI, ITU-T G.652 | Application | CWDM Metro, Access, DCI, Mobile Fronthaul |
10G CWDM SFP+ 1610nm 20km Optical Transceiver
The LINK-PP LS-CW6110-20C is a 10Gbps Coarse Wavelength Division Multiplexing (CWDM) SFP+ optical transceiver module engineered for single-mode fiber (SMF) links up to 20 km at a nominal channel wavelength of 1610 nm. Incorporating an internal DFB CWDM laser transmitter, PIN photodiode receiver with integrated trans-impedance preamplifier (TIA), and micro-controller unit (MCU), the module delivers stable optical power and real-time digital optical monitoring (DOM) across the commercial 0°C to +70°C operating temperature range.
The transceiver conforms to the SFP+ Multi-Source Agreement (MSA), SFF-8431 electrical interface specifications, and SFF-8472 diagnostic monitoring standards. Featuring a standard duplex LC/UPC optical interface and low power consumption, the LS-CW6110-20C provides a standardized pluggable solution suited for CWDM metro access networks, mobile fronthaul (CPRI/eCPRI), data center interconnects (DCI), and enterprise switching hardware.
Compatibility and Design Positioning
The LINK-PP LS-CW6110-20C is positioned as a cross-reference and alternative sourcing option for the Ciena CWDM-SFP10G-1610 10G CWDM 1610nm 20km SFP+ optical transceiver. The two devices share matching physical form factors, optical wavelength assignments (1610 nm CWDM channel), link reach up to 20 km over standard G.652 SMF, duplex LC optical interfaces, and SFF-8472 DOM support. LINK-PP transceivers can be pre-coded and tested for host platform recognition across compatible networking switches and optical transport platforms. Sourcing and engineering teams should verify host port compatibility, EEPROM coding requirements, and optical power budget margins against official documentation before deployment.
Procurement and OEM Qualification
For sourcing teams and OEM engineering programs evaluating the LS-CW6110-20C as a second-source or BOM alternative, key qualification parameters include host port interoperability, EEPROM coding compatibility, optical link budget margins, DOM telemetry calibration, operating temperature rating, and expected volume demand. LINK-PP can support sample evaluation, mechanical drawing review, and documentation requirements for prototype validation, AVL qualification, and volume production planning.
CWDM Optical Link Budget and 1610nm Fiber Transmission
Implementing 1610 nm CWDM optics in an SFP+ form factor provides specific bandwidth expansion and physical deployment advantages for optical transport systems:
- Fiber Exhaust Mitigation: Operating on the 1610 nm CWDM channel grid (ITU-T G.694.2) allows network operators to multiplex up to 18 independent optical channels onto a single dark fiber pair using passive CWDM multiplexer/demultiplexer filters.
- 20 km Optical Power Budget: With a minimum transmitter output power of -1 dBm and a receiver sensitivity of -16 dBm, the module provides a 15 dB optical link budget suitable for metro access rings, campus backbones, and cell site aggregation.
- Standard SFP+ Hot-Pluggable Envelope: The transceiver adheres to MSA physical dimensions, allowing hot insertion and extraction into high-density 10G line cards and top-of-rack switches without powering down the host platform.
- Duplex LC/UPC Interface: Standard duplex LC optical ports ensure broad compatibility with existing fiber patch panels and field-terminated single-mode optical cabling.
- 0°C to +70°C Commercial Operating Range: The 0°C to +70°C specification defines the verified operating temperature range, supporting standard enterprise wiring closets, indoor data centers, and environmentally controlled telecom shelters.
Electro-Optical Architecture, Digital Diagnostics (DOM), and Protocols
The LS-CW6110-20C combines an uncooled distributed feedback (DFB) laser transmitter operating at 1610 nm with an integrated PIN photodiode receiver. The transmitter delivers optical output power between -1 dBm and +5 dBm, while the receiver stage supports a dynamic input range from -23 dBm to -6 dBm with an overload threshold of 0 dBm.
Real-time operating parameters are accessed through a 2-wire I2C interface compliant with SFF-8472 Digital Optical Monitoring (DOM). System administrators can monitor transceiver temperature, supply voltage, laser bias current, transmitted optical power (TX power), and received optical power (RX power). The module supports multi-protocol framing including 10GBASE-ER/CWDM Ethernet, CPRI Option 7/8, and eCPRI, and complies with Class 1 laser safety standards under IEC 60825-1.
Host Board and Mechanical Integration Considerations
When integrating the LS-CW6110-20C into host line cards and optical systems, hardware and network engineers should account for the following structural and electrical parameters:
1. SFP+ Cage and Front-Panel Clearance
The transceiver housing adheres to SFF-8432 mechanical cage specifications. Chassis front panels should ensure unimpeded operation of the bail latch mechanism to allow easy insertion and removal in high-density multi-port switch faceplates.
2. High-Speed SFI Electrical Interface
The host PCB high-speed differential traces (TX+/- and RX+/-) should be routed as 100 Ω differential impedance lines with matched electrical lengths and AC-coupling capacitors, minimizing jitter and signal reflections at 10.3125 Gbps.
3. I2C Bus and DOM Telemetry Management
Host controller boards require appropriate pull-up resistors (typically 4.7 kΩ to 10 kΩ) on the MOD-DEF (SDA/SCL) lines to ensure stable I2C bus communication for DOM polling and module identification EEPROM access.
4. Optical Fiber Cleanliness and Attenuation Testing
Because CWDM channels at 1610 nm are sensitive to macro-bend losses and connector contamination, optical end-faces should be inspected and cleaned prior to insertion. During short-distance bench testing, inline optical attenuators must be used to keep received optical power below the 0 dBm overload limit.
Design Consideration Comparison: CWDM SFP+ vs. Alternative Optical Deployments
| Design Consideration | LS-CW6110-20C 10G 1610nm CWDM SFP+ |
Standard 10G 1310nm LR SFP+ (Point-to-Point) |
10G DWDM SFP+ Transceiver |
|---|---|---|---|
| Optical Wavelength Strategy | Fixed 1610 nm channel (20 nm channel grid) | Standard 1310 nm center wavelength | Dense grid channels (50 GHz / 100 GHz spacing) |
| Fiber Utilization Efficiency | Multiplexes up to 18 channels on single fiber pair | Requires dedicated fiber pair per 10G link | Multiplexes 40 to 80+ channels on single fiber pair |
| Passive Optical Mux Requirements | Requires passive CWDM Mux/Demux filter | Direct point-to-point fiber connection | Requires active or passive DWDM Mux/Demux |
| Rated Transmission Reach | 20 km on standard G.652 SMF | 10 km on standard G.652 SMF | 40 km to 80 km (Amplified spans supported) |
| Deployment Cost Profile | Moderate transceiver cost; high fiber savings | Lowest optical module cost; high fiber leasing cost | Higher optical module and filter infrastructure cost |
| Primary Engineering Focus | Fiber exhaust relief across metro and campus links | Direct switch-to-switch short/intermediate interconnects | High-capacity regional and long-haul core transport |
Application Considerations for LS-CW6110-20C
| Target Application Profile | Primary Engineering Consideration |
|---|---|
| CWDM Metro Access & Transport Rings | Enables 10 Gbps wavelength overlays on existing fiber routes using 1610 nm optical add-drop multiplexers (OADM). |
| Wireless Fronthaul & C-RAN (CPRI/eCPRI) | Transports multi-gigabit baseband traffic between central offices and remote radio heads over shared feeder fibers. |
| Data Center Interconnect (DCI) | Relieves dark fiber constraints between campus facilities across distances up to 20 km without active transponders. |
| Enterprise Aggregation on Ciena Platforms | Provides verified optical form-factor compatibility for Ciena switches and optical transport platforms. |
Engineering Verification Checklist
Before releasing an optical design or issuing volume procurement orders for the LS-CW6110-20C, engineering teams should confirm the following technical parameters:
- Optical Power Budget Calculation: Verify total link insertion loss—including fiber attenuation, patch panels, splices, and passive CWDM Mux/Demux insertion loss—remains within the 15 dB budget.
- Wavelength Filter Alignment: Ensure the passive optical multiplexer port is accurately centered at 1610 nm with an appropriate passband width (±6.5 nm typical).
- Host Compatibility and EEPROM Coding: Confirm host switch platform compatibility and verify that transceiver EEPROM programming aligns with target platform vendor expectations.
- Receiver Overload Protection: Ensure input optical power does not exceed the 0 dBm receiver overload limit; implement fixed optical attenuators if link distance is under 5 km.
- Fiber End-Face Inspection: Clean and inspect all LC/UPC connectors with an optical scope to prevent connector damage and high back-reflection.
- Operating Thermal Environment: Ensure chassis cage airflow keeps the transceiver case temperature within the specified 0°C to +70°C operating window.
Frequently Asked Questions
What are the primary specifications of the LINK-PP LS-CW6110-20C?
The LS-CW6110-20C is a 10Gbps CWDM SFP+ optical transceiver module. It features a nominal wavelength of 1610 nm, single-mode fiber (SMF) reach up to 20 km, duplex LC/UPC optical interface, DFB CWDM laser transmitter, PIN photodiode receiver, real-time SFF-8472 DOM support, and an operating temperature range of 0°C to +70°C.
Is the LINK-PP LS-CW6110-20C compatible with the Ciena CWDM-SFP10G-1610?
The LS-CW6110-20C is positioned as a cross-reference and alternative sourcing option for the Ciena CWDM-SFP10G-1610. Both modules share matching SFP+ form factors, 1610 nm optical wavelength channels, 20 km transmission distance, duplex LC interfaces, and DOM capabilities. Engineering teams should confirm switch EEPROM coding requirements prior to deployment.
What is the optical link budget for the LS-CW6110-20C?
The module specifies a minimum optical transmit power of -1 dBm and a receiver sensitivity of -16 dBm, resulting in a nominal optical power budget of 15 dB. Total link attenuation—including fiber dispersion loss, connector insertions, and passive CWDM filter insertion loss—must not exceed this budget.
What is Digital Optical Monitoring (DOM) and how is it accessed?
Digital Optical Monitoring (DOM, also known as DDM) provides real-time telemetry on transceiver operating conditions in accordance with SFF-8472. It allows host networking equipment to read parameters such as optical transmit power, optical receive power, internal temperature, laser bias current, and supply voltage via the two-wire I2C interface.
Why is the receiver overload threshold of 0 dBm important during installation?
An optical receiver overload threshold of 0 dBm defines the maximum optical power the internal PIN photodiode can receive without saturation or physical damage. During laboratory bench testing or short-distance link deployment, optical attenuators must be inserted to reduce received power below -6 dBm to prevent bit error rate (BER) degradation.
What type of optical fiber and connector does this transceiver require?
The LS-CW6110-20C requires standard 9/125 µm Single Mode Fiber (SMF, ITU-T G.652) terminated with Duplex LC/UPC (Ultra Physical Contact) optical connectors. It should not be used with multimode fiber or angled LC/APC connectors without appropriate mode-conditioning or adapter assemblies.
Packaging, Shipping and Global Delivery for Networking Products
Anti-static packaging, shock-resistant protection, fast order dispatch, and reliable worldwide delivery for all LINK-PP networking products.
Anti-Static Protective Packaging
Protect networking products from electrostatic discharge and handling-related damage.
Shock-Resistant Transport Protection
Protect products against physical impacts during storage and international transportation.
Fast Order Processing and Dispatch
Accelerate order handling to ensure quick warehouse deployment.
Global Logistics and International Delivery
Ship products efficiently to customers across worldwide locations.
10G SFP+ Technical Support and Deployment Assistance
LINK-PP provides expert technical support, from product selection and compatibility verification to deployment and long-term operation.
Pre-Sales Technical Consultation
Technical consultation to help you verify CWDM-SFP10G-1610 compatibility and select the appropriate product for your application.
Compatibility Verification Support
Verification support to help ensure compatibility with your equipment, applications, and deployment requirements.
Deployment & Installation Assistance
Comprehensive step-by-step guidance for installation, configuration, and initial setup, ensuring accurate deployment and reliable, stable operation from the start.
Long-Term Technical Assurance
Ongoing technical support throughout the product lifecycle, delivering long-term stability for enterprise and carrier-grade networks.
Industry Standards, Compliance and Quality Assurance
LINK-PP products are manufactured under recognized quality management systems and designed to support applicable industry standards, regulatory compliance, and long-term deployment requirements, including IEEE 802.3, RoHS, REACH, ISO 9001, and ISO 14001 where applicable. 「View Quality & Compliance Center」
ISO 9001 Quality Management
Manufactured under certified quality management processes to ensure consistent product quality and production control.
IEEE 802.3 Standards Compliance
Designed in accordance with applicable networking and Ethernet standards, including IEEE specifications where relevant.
RoHS Compliance
Manufactured using materials that support restrictions on hazardous substances for global market requirements.
REACH Compliance
Material declarations and supply chain processes support applicable REACH regulatory requirements.
Product Safety Assurance
Selected products support recognized safety and reliability requirements for networking applications.
Reliability Verification Testing
Products undergo verification and quality testing to support stable operation in enterprise, telecom, and industrial environments.
10G SFP+ Warranty and After-Sales Service
LINK-PP provides warranty coverage and after-sales support to help ensure stable operation and long-term product performance.
15-day no-reason return and refund
Free replacement for dead-on-arrival (DOA) or defective items within the initial period
Free repair services for manufacturing defects throughout the warranty period
Warranty exclusions and conditions apply
Keyword:
SFP Download
Product Drawing
Ciena Compatible 10G CWDM-SFP10G-1610 FAQ
Recommend
-
Nav Menu
-
About LINK-PP
-
All Products
-
Applications







































