HOT CROSS-REFERENCE SEARCHES All Products
HR911105A Cisco GLC-LH-SMD Pulse J1011F21PNL LPJG0926HENL TE 2170704-1 SFP-10G-SR
POPULAR CATEGORIES
Matched Parts (Real-time ES) Use ↑ ↓ to select, Enter to open
+
  • LS-CW6110-40C-1.webp
  • LS-CW6110-40C-2.webp
  • LS-CW6110-40C-3.webp
  • LS-CW6110-40C-4.webp
  • LS-CW6110-40C-5.webp

Ciena CWDM-SFP10G-1610 Compatible LS-CW6110-40C SFP+ 10G CWDM 1610nm 40km DOM Duplex LC/UPC SMF Optical Transceiver Module

P/N:

LS-CW6110-40C

Manufacturer:

LINK-PP

Classification:

Compatible Brand:

Ciena

Compatible P/N:

CWDM-SFP10G-1610

  • Compatible Brands: Ciena
  • Form Factor: SFP+
  • Data Rate: 10G
  • Distance: ≤40km
  • Type: Single Mode
  • Connector: Duplex LC
  • Wavelength: 1350nm-1610nm
  • P/N: LS-CW6110-40C
  • Manufacture: LINK-PP
  • Compatible Brand: Ciena
  • Compatible P/N: CWDM-SFP10G-1610

Product Specifications

LINK-PP Part Number LS-CW6110-40C Ciena Part Number Equivalent CWDM-SFP10G-1610
Form Factor SFP+ Part Status Active
Max Data Rate 10Gbps Optical Wavelength 1610nm (CWDM)
Max Transmission Distance 40km Optical Media Single Mode Fiber (SMF, G.652)
Optical Connector Duplex LC/UPC Transmitter Type DFB CWDM
Receiver Type PIN Photodiode DOM Support Yes (SFF-8472)
TX Optical Power -1 to +5 dBm RX Optical Power Range -23 to -6 dBm
Receiver Sensitivity -16 dBm Receiver Overload 0 dBm
Operating Temperature 0°C to +70°C (Commercial) Standard Compliance SFP+ MSA, SFF-8431, SFF-8472, IEEE 802.3ae, Class 1 Laser
Protocols Supported 10GBASE Ethernet, CPRI, eCPRI, ITU-T G.694.2 Application CWDM Metro, Regional Transport, DCI, Enterprise Backbones

10G CWDM SFP+ 1610nm 40km Optical Transceiver

The LINK-PP LS-CW6110-40C is a high-performance 10Gbps Coarse Wavelength Division Multiplexing (CWDM) SFP+ optical transceiver module engineered for single-mode fiber (SMF) links up to 40 km at a nominal channel wavelength of 1610 nm. Incorporating an internal DFB CWDM laser transmitter, PIN photodiode receiver with integrated trans-impedance preamplifier (TIA), and micro-controller unit (MCU), the module delivers stable optical power and real-time digital optical monitoring (DOM) across the commercial 0°C to +70°C operating temperature range.

The transceiver conforms to the SFP+ Multi-Source Agreement (MSA), SFF-8431 electrical interface specifications, SFF-8472 diagnostic monitoring standards, and IEEE 802.3ae 10GBASE Ethernet protocols. Featuring a standard duplex LC/UPC optical interface, the LS-CW6110-40C provides an extended-reach optical solution suited for CWDM metro access rings, regional transport networks, long-span data center interconnects (DCI), and enterprise switching infrastructure.

Lifecycle: Active
Form Factor & Speed: SFP+ 10Gbps
Wavelength & Reach: 1610nm CWDM / 40km SMF
Cross Reference: Ciena CWDM-SFP10G-1610
Operating Temperature: 0°C to +70°C Commercial
Qualification Support: Sample Evaluation / Second Source

Compatibility and Design Positioning

The LINK-PP LS-CW6110-40C is positioned as a cross-reference and alternative sourcing option for the Ciena CWDM-SFP10G-1610 10G CWDM 1610nm SFP+ optical transceiver. The two devices share matching physical form factors, optical wavelength assignments (1610 nm CWDM channel), link reach up to 40 km over standard G.652 SMF, duplex LC optical interfaces, and SFF-8472 DOM support. LINK-PP transceivers can be pre-coded and tested for host platform recognition across compatible networking switches and optical transport platforms. Sourcing and engineering teams should verify host port compatibility, EEPROM coding requirements, and optical power budget margins against official documentation before deployment.

Procurement and OEM Qualification

For sourcing teams and OEM engineering programs evaluating the LS-CW6110-40C as a second-source or BOM alternative, key qualification parameters include host port interoperability, EEPROM coding compatibility, optical link budget margins, DOM telemetry calibration, operating temperature rating, and expected volume demand. LINK-PP can support sample evaluation, mechanical drawing review, and documentation requirements for prototype validation, AVL qualification, and volume production planning.

CWDM Optical Link Budget and 1610nm 40km Fiber Transmission

Implementing 1610 nm CWDM optics for 40 km spans in an SFP+ form factor provides specific bandwidth expansion and extended-reach deployment advantages for optical transport systems:

  • Fiber Exhaust Mitigation: Operating on the 1610 nm CWDM channel grid (ITU-T G.694.2) allows network operators to multiplex multiple independent 10G optical channels onto existing dark fiber pairs using passive CWDM multiplexer/demultiplexer filters.
  • 40 km Extended Reach on G.652 SMF: Engineered to cover long metro and regional spans where standard 10 km or 20 km optics cannot satisfy optical link distance and filter insertion loss requirements.
  • Standard SFP+ Hot-Pluggable Envelope: The transceiver adheres to MSA physical dimensions, allowing hot insertion and extraction into high-density 10G line cards and top-of-rack switches without powering down the host platform.
  • Duplex LC/UPC Interface: Standard duplex LC optical ports ensure broad compatibility with existing fiber distribution frames and field-terminated single-mode optical cabling.
  • 0°C to +70°C Commercial Operating Range: The 0°C to +70°C specification defines the verified operating temperature range, supporting standard enterprise wiring closets, indoor data centers, and environmentally controlled telecom shelters.

Electro-Optical Architecture, Digital Diagnostics (DOM), and Protocols

The LS-CW6110-40C combines a distributed feedback (DFB) laser transmitter operating at 1610 nm with an integrated PIN photodiode receiver. The transmitter delivers optical output power between -1 dBm and +5 dBm, while the receiver stage supports a dynamic input range from -23 dBm to -6 dBm with an overload threshold of 0 dBm.

Real-time operating parameters are accessed through a 2-wire I2C interface compliant with SFF-8472 Digital Optical Monitoring (DOM). System administrators can monitor transceiver temperature, supply voltage, laser bias current, transmitted optical power (TX power), and received optical power (RX power). The module supports multi-protocol framing including IEEE 802.3ae 10GBASE Ethernet, CPRI, and eCPRI, and complies with Class 1 laser safety standards under IEC 60825-1.

Host Board and Mechanical Integration Considerations

When integrating the LS-CW6110-40C into host line cards and optical systems, hardware and network engineers should account for the following structural and electrical parameters:

1. SFP+ Cage and Front-Panel Clearance

The transceiver housing adheres to SFF-8432 mechanical cage specifications. Chassis front panels should ensure unimpeded operation of the bail latch mechanism to allow easy insertion and removal in high-density multi-port switch faceplates.

2. High-Speed SFI Electrical Interface

The host PCB high-speed differential traces (TX+/- and RX+/-) should be routed as 100 Ω differential impedance lines with matched electrical lengths and AC-coupling capacitors, minimizing jitter and signal reflections at 10.3125 Gbps.

3. I2C Bus and DOM Telemetry Management

Host controller boards require appropriate pull-up resistors (typically 4.7 kΩ to 10 kΩ) on the MOD-DEF (SDA/SCL) lines to ensure stable I2C bus communication for DOM polling and module identification EEPROM access.

4. Optical Attenuation During Bench Verification

Because the receiver overload threshold is 0 dBm and sensitivity is rated to -16 dBm, short-distance testing in lab environments or deployments under 10 km must incorporate inline optical attenuators to prevent optical receiver saturation and avoid bit error rate (BER) penalties.

Design Consideration Comparison: CWDM SFP+ vs. Alternative Optical Deployments

Design Consideration LS-CW6110-40C
10G 1610nm 40km CWDM SFP+
Standard 10G 1310nm LR SFP+
(Point-to-Point)
10G DWDM SFP+
Transceiver (Long Haul)
Optical Wavelength Strategy Fixed 1610 nm channel (20 nm channel grid) Standard 1310 nm center wavelength Dense grid channels (50 GHz / 100 GHz spacing)
Fiber Utilization Efficiency Multiplexes up to 18 channels on single fiber pair Requires dedicated fiber pair per 10G link Multiplexes 40 to 80+ channels on single fiber pair
Passive Optical Mux Requirements Requires passive CWDM Mux/Demux filter Direct point-to-point fiber connection Requires active or passive DWDM Mux/Demux
Rated Transmission Reach 40 km on standard G.652 SMF 10 km on standard G.652 SMF 40 km to 80 km (Amplified spans supported)
Deployment Cost Profile Moderate transceiver cost; high fiber savings Lowest optical module cost; high fiber leasing cost Higher optical module and filter infrastructure cost
Primary Engineering Focus Long-reach fiber exhaust relief across metro links Direct switch-to-switch short/intermediate interconnects High-capacity regional and long-haul core transport

Application Considerations for LS-CW6110-40C

Target Application Profile Primary Engineering Consideration
Extended-Reach Metro Access & CWDM Rings Enables 10 Gbps wavelength overlays across metro distances up to 40 km using 1610 nm optical add-drop multiplexers (OADM).
Regional Optical Transport & OADM Nodes Transports aggregated 10G traffic across multi-node optical ring topologies without requiring intermediate electrical regeneration.
Long-Span Data Center Interconnect (DCI) Connects separated campus data centers across distances up to 40 km over leased dark fiber infrastructure.
Enterprise Core Aggregation on Ciena Platforms Provides verified optical form-factor compatibility for Ciena switches and optical transport platforms.

Engineering Verification Checklist

Before releasing an optical design or issuing volume procurement orders for the LS-CW6110-40C, engineering teams should confirm the following technical parameters:

  • Optical Power Budget Calculation: Verify total link insertion loss—including fiber attenuation (typically 0.25 dB/km at 1610 nm), patch panels, splices, and passive CWDM Mux/Demux insertion loss—remains within the module's link budget.
  • Wavelength Filter Alignment: Ensure the passive optical multiplexer port is accurately centered at 1610 nm with an appropriate passband width (±6.5 nm typical).
  • Host Compatibility and EEPROM Coding: Confirm host switch platform compatibility and verify that transceiver EEPROM programming aligns with target platform vendor expectations.
  • Receiver Overload Protection: Ensure input optical power does not exceed the 0 dBm receiver overload limit; implement fixed optical attenuators if link distance is under 10 km.
  • Fiber End-Face Inspection: Clean and inspect all LC/UPC connectors with an optical scope to prevent connector damage and high back-reflection.
  • Operating Thermal Environment: Ensure chassis cage airflow keeps the transceiver case temperature within the specified 0°C to +70°C operating window.

Frequently Asked Questions

What are the primary specifications of the LINK-PP LS-CW6110-40C?

The LS-CW6110-40C is a 10Gbps CWDM SFP+ optical transceiver module. It features a nominal wavelength of 1610 nm, single-mode fiber (SMF) reach up to 40 km, duplex LC/UPC optical interface, DFB CWDM laser transmitter, PIN photodiode receiver, real-time SFF-8472 DOM support, and an operating temperature range of 0°C to +70°C.

Is the LINK-PP LS-CW6110-40C compatible with the Ciena CWDM-SFP10G-1610?

The LS-CW6110-40C is positioned as a cross-reference and alternative sourcing option for the Ciena CWDM-SFP10G-1610. Both modules share matching SFP+ form factors, 1610 nm optical wavelength channels, duplex LC interfaces, and DOM capabilities. Engineering teams should confirm switch EEPROM coding requirements prior to deployment.

What optical fiber is required for 40 km transmission at 1610 nm?

The module requires standard 9/125 µm Single Mode Fiber (SMF, ITU-T G.652) terminated with Duplex LC/UPC connectors. Due to fiber attenuation and chromatic dispersion characteristics in the 1610 nm window, optical link budgets must be calculated carefully across the full 40 km span.

What is Digital Optical Monitoring (DOM) and how is it accessed?

Digital Optical Monitoring (DOM, also known as DDM) provides real-time telemetry on transceiver operating conditions in accordance with SFF-8472. It allows host networking equipment to read parameters such as optical transmit power, optical receive power, internal temperature, laser bias current, and supply voltage via the two-wire I2C interface.

Why are optical attenuators recommended during short-distance lab testing?

The optical transmitter outputs up to +5 dBm, while the receiver overload threshold is rated at 0 dBm. When testing on short fiber patch cords without the natural attenuation of a long fiber span or passive CWDM mux/demux filters, an inline optical attenuator must be inserted to prevent receiver saturation and bit error rate degradation.

What protocols and data rates does the LS-CW6110-40C support?

The LS-CW6110-40C supports standard 10 Gbps serial data streams, including IEEE 802.3ae 10GBASE-ER/CWDM Ethernet, CPRI, and eCPRI framing, making it versatile across data center, enterprise, and telecommunications network applications.

Packaging, Shipping and Global Delivery for Networking Products

Anti-static packaging, shock-resistant protection, fast order dispatch, and reliable worldwide delivery for all LINK-PP networking products.

Anti-Static Protective Packaging

Anti-Static Protective Packaging

Protect networking products from electrostatic discharge and handling-related damage.

Shock-Resistant Transport Protection

Shock-Resistant Transport Protection

Protect products against physical impacts during storage and international transportation.

Fast Order Processing and Dispatch

Fast Order Processing and Dispatch

Accelerate order handling to ensure quick warehouse deployment.

Global Logistics and International Delivery

Global Logistics and International Delivery

Ship products efficiently to customers across worldwide locations.

10G SFP+ Technical Support and Deployment Assistance

LINK-PP provides expert technical support, from product selection and compatibility verification to deployment and long-term operation.

Pre-Sales Technical Consultation

Pre-Sales Technical Consultation

Technical consultation to help you verify CWDM-SFP10G-1610 compatibility and select the appropriate product for your application.

Compatibility Verification Support

Compatibility Verification Support

Verification support to help ensure compatibility with your equipment, applications, and deployment requirements.

Deployment & Installation Assistance

Deployment & Installation Assistance

Comprehensive step-by-step guidance for installation, configuration, and initial setup, ensuring accurate deployment and reliable, stable operation from the start.

Long-Term Technical Assurance

Long-Term Technical Assurance

Ongoing technical support throughout the product lifecycle, delivering long-term stability for enterprise and carrier-grade networks.

Industry Standards, Compliance and Quality Assurance

LINK-PP products are manufactured under recognized quality management systems and designed to support applicable industry standards, regulatory compliance, and long-term deployment requirements, including IEEE 802.3, RoHS, REACH, ISO 9001, and ISO 14001 where applicable. 「View Quality & Compliance Center」

ISO 9001 Quality Management System Certification

ISO 9001 Quality Management

Manufactured under certified quality management processes to ensure consistent product quality and production control.

IEEE 802.3 Ethernet Standard Compliance

IEEE 802.3 Standards Compliance

Designed in accordance with applicable networking and Ethernet standards, including IEEE specifications where relevant.

RoHS Compliance

RoHS Compliance

Manufactured using materials that support restrictions on hazardous substances for global market requirements.

REACH Compliance

REACH Compliance

Material declarations and supply chain processes support applicable REACH regulatory requirements.

Product Safety Assurance

Product Safety Assurance

Selected products support recognized safety and reliability requirements for networking applications.

Reliability Verification Testing

Reliability Verification Testing

Products undergo verification and quality testing to support stable operation in enterprise, telecom, and industrial environments.

10G SFP+ Warranty and After-Sales Service

LINK-PP provides warranty coverage and after-sales support to help ensure stable operation and long-term product performance.

15 days

15-day no-reason return and refund

Free maintenance or replacement

Free replacement for dead-on-arrival (DOA) or defective items within the initial period

Free maintenance

Free repair services for manufacturing defects throughout the warranty period

Limitations

Warranty exclusions and conditions apply

Keyword:

SFP Download