HOT CROSS-REFERENCE SEARCHES All Products
HR911105A Cisco GLC-LH-SMD Pulse J1011F21PNL LPJG0926HENL TE 2170704-1 SFP-10G-SR
POPULAR CATEGORIES
Matched Parts (Real-time ES) Use ↑ ↓ to select, Enter to open

T568A vs T568B: The Definitive Guide to RJ45 Wiring Standards

LINK-PP

LINK-PP Official  ·

Jun 30,2025

A practical, expert-led comparison of T568A and T568B wire terminations for RJ45 connectors — pinouts, differences, common pitfalls, testing tips, and best practices for reliable installations.

What are T568A and T568B?

Both T568A and T568B are standardized RJ45 wiring schemes defined under the TIA/EIA structured cabling specifications. They specify the order of the eight conductors inside a twisted-pair Ethernet cable when terminated in an RJ45 connector.

T568A emphasizes compatibility with legacy telephone (USOC) wiring. T568B is derived from AT&T’s earlier 258A wiring and is the more prevalent choice in commercial and enterprise cabling. The only technical difference is the swap of the green and orange pairs; the practical impact comes from consistency across an installation.

Pinout configurations

Below are the pin assignments for each standard. Use this table when terminating or verifying cables.

RJ45 pinout — T568A vs T568B
Pin T568A T568B
1 Green-White Orange-White
2 Green Orange
3 Orange-White Green-White
4 Blue Blue
5 Blue-White Blue-White
6 Orange Green
7 Brown-White Brown-White
8 Brown Brown
T568A vs T568B wiring diagram showing swapped green and orange pairs

T568A and T568B difference: swapped positions of green and orange pairs.

Quick comparison: T568A vs T568B

Category T568A T568B
Origin USOC telephone compatibility Derived from AT&T 258A
Typical use Residential, some government contracts Commercial / enterprise networks
Prevalence Less common in enterprise Most widely used
Performance Equivalent electrically (minor crosstalk variance) Equivalent electrically (favored in dense panels)
When to choose Legacy systems that require USOC mapping New installations and business deployments

Does the choice affect performance?

For modern Ethernet applications, the wiring scheme itself does not change signal performance — performance is governed by cable category (Cat5e, Cat6, Cat6A, etc.), connector quality, termination quality, and testing. However, inconsistent wiring across your network can create functional problems:

  • Unintended crossover when one end is A and the other end is B.
  • Impedance mismatches or pair swaps that degrade link negotiation for multi-pair protocols.
  • Troubleshooting complexity and longer mean-time-to-repair (MTTR).

Pro tip: Choose one standard for the whole site and document it in wiring diagrams and labeling.

Common cabling mistakes & how to avoid them

  1. Mixing standards within a run — always confirm both ends match before commissioning.
  2. Untwisting pairs too far — keep untwist length to a minimum (typical recommendation: <13 mm / 1/2 inch at termination).
  3. Poor crimping — use certified crimp tools and perform pull tests for mechanical integrity.
  4. Using the wrong cable category — plan for the required bandwidth and headroom (choose Cat6A for future 10GBase-T needs).
  5. Skipping certification testing — always test links with a cable certifier for NEXT, FEXT, attenuation, and wiremap.

Best practice recommendations

Standardization

Lock in a single wiring standard for the entire installation. Update documentation and label each outlet and patch cable so teams never mix A and B inadvertently.

Quality & testing

Use reputable cable, connectors and tools. Certify every permanent link with a cable tester and keep the test reports for warranty and troubleshooting.

Practical termination tips

  • Strip jacket only as far as necessary; avoid exposing twisted pairs beyond the termination point.
  • Maintain pair twists as close to the IDC/crimp point as possible.
  • Perform an insertion & pull test after crimping to verify mechanical reliability.
  • Use keyed jack orientation and consistent labeling (port numbers, floor, room).

Frequently asked questions

Which is more common: T568A or T568B?

In most commercial and enterprise environments, T568B is more prevalent. Some government and residential builds may still specify T568A for backwards compatibility.

Can I mix T568A and T568B in one building?

Only if each cable run is terminated consistently on both ends. Mixing standards on the same cable creates a crossover and will confuse normal patching expectations.

Does T568A vs T568B affect PoE?

No. Power over Ethernet works with either wiring as long as the cable and terminations meet the required category and quality standards.

How do I test a terminated cable?

Use a certified cable tester to run a full certification report (wiremap, NEXT, return loss, attenuation). For simple checks, a wiremap tester will validate pair order and continuity.

Which should I choose for new installations?

Unless a specification calls for T568A, adopt T568B for consistency with common enterprise practice. The crucial factor is consistency and correct testing, not which scheme you pick.

Related resources & call to action

For detailed diagrams and related product information, consult these resources:

If you need tested patch cords, high-quality RJ45 jacks, or certified Cat6A assemblies for your next project, using factory-tested components reduces on-site failures and speeds deployment.

Browse RJ45 Connector

Authoritative guidance provided by experienced cabling professionals. For installation services, certification, or technical consulting, contact LINK-PP or your preferred cabling specialist.

Need More Information?

Submit your inquiry and our team will respond shortly.
Send Inquiry to Engineering Team