Product Categories
Namibia HR911205 Compatible LINK-PP LPJ26204ABNL 10/100 Base-T 8p8c Tab Down Green/Yellow LED 1x2 Port RJ45 Jack
- Number of Ports: 1X2
- Speed: 10Base-T,100Base-TX
- PoE: Non-PoE
- Latch: Down
- LED Option: Green / Yellow
- Shield EMI Tabs: YES
- Temperature: 0℃ to 70℃
- P/N: LPJ26204ABNL
- Manufacturer: LINK-PP
- Compatible Brand: LINK-PP
- Compatible P/N: HR911205
Category:
Product Description
Product Specifications
| LINK-PP Part Number | LPJ26204ABNL | Part Number | HR911205 |
| Part Status | Active | Connector Type | Jack |
| Number of Positions/Contacts | 8P8C (RJ45, Ethernet) | Application-LAN | Ethernet (Non-PoE) |
| Number of Ports | 1x2 Port | Speed | 10/100BASE-T |
| Latch | Down | Cores per Port | 4 |
| Orientation | 90° Angle (Right) | PCB Mount Angle | Side Entry |
| Shield EMI Tabs | With | LED Option | Green / Yellow |
| PCB | FR4 | PCB Retaining Post | T-Post |
| Package Height (Inches/mm) | 0.536 / 13.61 | Package Length (Inches/mm) | 0.841 / 21.36 |
| Package Width (Inches/mm) | 1.228 / 31.18 | Temperature | 0°C to +70°C |
| BST Circuit | Yes | AutoMDX | Yes |
| Diodes | No | Contact Mating Area Plating | Gold 6µ" / 15µ" / 30µ" |
| Turns Ratio RX/TX | 1CT:1CT | Configuration RX/TX | T, C |
HR911205 Compatible Dual-Port 1x2 10/100BASE-T Integrated RJ45 MagJack
The LINK-PP LPJ26204ABNL is a dual-port (1x2) horizontal integrated RJ45 MagJack engineered for 10/100BASE-T Fast Ethernet applications in non-PoE network architectures. Featuring a Tab-Down orientation, a compact package length of 21.36 mm (0.841 inches), and a commercial operating temperature range of 0°C to +70°C, it combines two 8P8C modular interfaces with integrated 4-core magnetic circuitry per port, Bob Smith termination, and Green/Yellow status LEDs inside a shielded through-hole housing.
The connector features a 90° right-angle, side-entry profile with perimeter EMI grounding tabs, T-Post mechanical PCB retention, and a 31.18 mm overall horizontal width. It is positioned as a compatible alternative to the HR911205 for game controllers, industrial automation equipment, network interface cards (NICs), optical network terminals (ONT), and embedded computing systems where board depth, dual-port alignment, and upper panel clearances are primary design constraints.
Hardware designers should verify the mechanical drawing, pin assignment, PCB land pattern, and PHY manufacturer interface guidelines against product documentation before releasing PCB layouts for production.
HR911205 Compatible Design Positioning
The LPJ26204ABNL is positioned as a compatible alternative to the HR911205 for 10/100BASE-T Fast Ethernet applications, providing hardware engineering and procurement teams with a potential second-source option for designs requiring comparable package, footprint, and electrical interface characteristics.
To ensure proper integration on existing or new motherboard designs, engineering teams should cross-reference the mechanical drawing, pin assignment, solder pad geometry, and electrical characteristics against original design requirements prior to volume release.
Horizontal 1x2 Topology and Tab-Down Latch Geometry
Multi-port board layout and enclosure geometry influence connector selection for front-panel Ethernet interfaces:
- Unified 1x2 Dual-Port Alignment: A single 1x2 ganged connector maintains the defined port spacing within one 31.18 mm housing, simplifying front-panel alignment compared with two independently placed single-port connectors.
- Tab-Down Accessibility: In systems where the connector is positioned near an upper enclosure edge, under an overhang, or beneath a bezel, the Tab-Down latch places the release tab on the lower side and can improve cable-release accessibility when sufficient clearance is provided.
- Compact 21.36 mm Package Length: The 21.36 mm package length reduces connector depth relative to larger dual-port designs, which can leave additional board area behind the connector for routing and supporting components.
- Metal Shielding with EMI Tabs: Perimeter spring-finger grounding tabs around the metal shell establish contact with the equipment front panel or bezel cutout, supporting the system-level shielding and grounding architecture.
10/100BASE-T Signal Transmission and Integrated Magnetics
Fast Ethernet (100BASE-TX) communication utilizes two differential pairs per port: one dedicated to transmit (TX) and one to receive (RX). The LPJ26204ABNL incorporates integrated 4-core magnetic circuitry per channel with a 1CT:1CT turns ratio (T, C configuration) to support physical-layer signal coupling across the commercial 0°C to +70°C operating temperature range.
Because the connector is engineered specifically for non-PoE architectures, the internal magnetic layout is dedicated to differential data transmission without allocating space or thermal margins to high-current DC power paths.
Hardware designers should evaluate the MagJack in conjunction with the host Fast Ethernet PHY transceivers, differential trace layout, ground plane design, and enclosure EMC strategy to ensure proper physical-layer performance.
Mechanical and PCB Design Considerations
Physical mounting orientation and board anchoring are key considerations when integrating dual-port through-hole RJ45 jacks:
1. 8P8C Interface per Port and PCB Termination
Each port features a standard 8-contact RJ45 mating face alongside through-hole termination pins on the PCB side. Engineers should consult the official mechanical and electrical drawings to verify the terminal assignment, LED connections, and magnetic interface before releasing board artwork.
2. T-Post Mechanical Retention
Molded T-Post locating features help position and mechanically retain the dual-port connector body on the FR4 PCB. The host PCB layout and solder joints should be evaluated together to ensure adequate mechanical support during cable insertion and removal.
3. Status LED Indicators
The connector incorporates Green and Yellow LEDs on each port for visual link and network activity indication. Current-limiting resistors and drive circuits must be implemented on the host PCB in accordance with PHY specifications and LED electrical ratings.
Architecture Comparison: Dual-Port 1x2 MagJack vs. Alternative Implementations
| Evaluation Metric | LPJ26204ABNL 1x2 Tab-Down 10/100 MagJack |
2 x Single-Port 10/100 MagJacks |
Stacked 2x1 10/100 MagJack |
|---|---|---|---|
| Port Configuration | 1x2 Horizontal Ganged | 2 x Discrete Single Ports | Stacked 2x1 (Vertical 2-Port) |
| Vertical Height Profile | Low-Profile (~13.61 mm) | Low-Profile (~13.50 mm) | Tall (~25.50 mm) |
| Operating Temperature | 0°C to +70°C (Commercial) | 0°C to +70°C | Model-dependent |
| Package Length (Depth) | Compact (21.36 mm / 0.841 in) | Typically 25.25 mm – 32.50 mm | Typically 28.50 mm |
| Latch Orientation | Tab-Down (Bottom Latch) | Tab-Up or Tab-Down | Dual Latch (Both) |
| Assembly Placement | Single placement cycle | Two individual placements required | Single placement cycle |
| Primary Advantage | Low vertical profile with compact depth for dual I/O | Flexible port spacing | Saves horizontal board-edge space |
Application Considerations for LPJ26204ABNL
| Target Application Profile | Potential Plating Option | Primary Engineering Consideration |
|---|---|---|
| Game Hardware & Multi-Media Controllers | Gold 6µ" / 15µ" | Low-profile 13.61 mm height fits compact consumer housings; dual-port consolidation simplifies assembly. |
| Factory Automation & Embedded Control Systems | Gold 15µ" / 30µ" | Reliable 10/100BASE-T Fast Ethernet connectivity, T-Post mechanical PCB retention. |
| Network Interface Cards & Server Adapters | Gold 15µ" | Compact 21.36 mm connector depth can help preserve PCB area for PHY routing and supporting circuitry. |
| Optical Network Terminals (ONT) & Gateways | Gold 6µ" / 15µ" | Perimeter EMI tabs for chassis grounding; Tab-Down latch improves maintenance access in top-panel layouts. |
Engineering Verification Checklist
Before releasing a PCB layout or finalizing a bill of materials (BOM) using the LPJ26204ABNL, hardware engineers should confirm the following design parameters against the official product drawing:
- Package Dimensions & Clearances: Verify the 13.61 mm height, 21.36 mm length, and 31.18 mm width against internal enclosure clearances.
- Pinout and Schematic Alignment: Verify the terminal numbering, center-tap connections, and differential-pair assignments against the official product drawing and selected PHY reference design.
- Tab-Down Latch Clearance: Ensure adequate clearance below the front-panel cutout for RJ45 plug latch disengagement during maintenance.
- PCB Land Pattern: Check through-hole pad diameters, T-Post hole locations, and shield ground pin drill sizes on the manufacturer's footprint drawing.
- EMI Tab Contact Geometry: Confirm front-panel cutout dimensions ensure mechanical contact with the shield EMI spring tabs.
- LED Drive Circuitry: Implement suitable series current-limiting resistors and drive circuits on the host PCB matched to the selected PHY.
- Thermal Operating Environment: Validate that the component operating environment remains within the specified 0°C to +70°C commercial range.
Frequently Asked Questions
Is the LINK-PP LPJ26204ABNL a compatible alternative to the HR911205?
The LPJ26204ABNL is designed as a compatible alternative to the HR911205 with a dual-port (1x2) 10/100BASE-T MagJack configuration, Tab-Down latch, compact 21.36 mm package length, 8P8C pinout per port, Green/Yellow LEDs, T-Post PCB retention, metal shield with EMI tabs, and a commercial operating temperature range of 0°C to +70°C. Engineers should verify the mechanical drawing, pin assignments, and PCB land pattern before production use.
What is the mechanical advantage of a 1x2 horizontal ganged connector?
A 1x2 horizontal ganged connector maintains defined port spacing within a single 31.18 mm housing, simplifying front-panel alignment compared with two independently placed single-port connectors. It also reduces component placement cycles during board assembly.
What is the design benefit of the Tab-Down latch and 21.36 mm package length?
The Tab-Down latch places the release tab on the lower side of the connector, which can improve cable-release accessibility when mounted near an upper enclosure edge or beneath a display bezel. The compact 21.36 mm length reduces depth requirements on the PCB relative to larger dual-port alternatives.
What is the function of the 4-core magnetic design per port?
The LPJ26204ABNL specifies four magnetic cores per Ethernet port for its integrated 10/100BASE-T interface. These magnetic components support the electrical interface between the Ethernet PHY and the cable-side RJ45 connection. Engineers should refer to the product schematic and electrical specification for the exact magnetic topology and termination arrangement.
Is the LPJ26204ABNL suitable for Power over Ethernet (PoE)?
No. The LPJ26204ABNL is specified as a Non-PoE connector for data-only Fast Ethernet interfaces. For systems requiring PoE power delivery, a MagJack with dedicated PoE-rated magnetics and DC current paths should be selected.
What contact plating options are available for the LPJ26204ABNL?
The LPJ26204ABNL is available with 6 micro-inch, 15 micro-inch, or 30 micro-inch gold plating options at the contact mating area. Selection should be evaluated based on the expected mating cycles, operating environment, and application durability requirements.
Download
Product Drawing
3D Model
-
Nav Menu
-
About LINK-PP
-
All Products
-
Applications



























