Product Categories
Costa-Rica 64F-1301GYD2NL Compatible LINK-PP LPJG46801AENL 10/100/1000 Base-T Tab Down Green/Yellow LED 1x4 Port Ethernet RJ45 Connection
- Number of Ports: 1X4
- Speed: 10Base-T,100Base-TX,1000Base-T
- PoE: Non-PoE
- Latch: Down
- LED Option: Green / Yellow
- Shield EMI Tabs: YES
- Temperature: 0℃ to 70℃
- P/N: LPJG46801AENL
- Manufacturer: LINK-PP
- Compatible Brand: LINK-PP
- Compatible P/N: 64F-1301GYD2NL
Category:
Product Description
Product Specifications
| LINK-PP Part Number: | LPJG46801AENL | Part Number | 64F-1301GYD2NL |
| Part Status | Active | Connector Type | Jack |
| Number of Positions/Contacts | 10p8c (RJ45, Ethernet) | Application-Lan | Ethernet(Non-PoE) |
| Number of Ports | 1x4 Port | Speed | 10/100/1000 Base-T |
| Latch | Down | Cores per Port | 8 |
| Orientation | 90° Angle (Right) | PCB Mount Angle | SIDE ENTRY |
| Shield EMI Tabs | With | LED Option | Green/Yellow Led |
| PCB | FR4 | PCB Retaining Post | T POST |
| Package Height (Inches/mm) | 0.533/13.55 | Package Length (Inches/mm) | 0.839/21.30 |
| Package Width (Inches/mm) | 2.328/59.12 | Temperature | 0℃ TO 70℃ |
| Bst Circuit | Yes | AutomDX | YES |
| Diodes | No | Contact Mating Area Plating | GOLD 6u"/15u"/30u" |
| Turns Ratio RX/TX | 1CT:1CT | Configuration RX/TX | T,C |
Product Engineering Overview
LINK-PP LPJG46801AENL combines a 1×4 10/100/1000 Base-T RJ45 port arrangement with integrated magnetics in a side-entry PCB-mounted assembly. The product record lists a Tab Down latch and green/yellow.
The record specifies Non-PoE operation and an operating range of 0°C to 70°C. Its listed body dimensions are 59.12 × 21.30 × 13.55 mm; check the board and enclosure together when arranging the connector.
Compatibility and Design Positioning
The existing record positions LPJG46801AENL as a cross-reference and alternative sourcing option for 64F-1301GYD2NL. Compare both official drawings, magnetic characteristics, footprint, LED pins and panel geometry before qualifying a substitution; the listing alone does not prove interchangeability.
Procurement and OEM Qualification
Specify LPJG46801AENL and the applicable drawing revision when requesting samples. Confirm plating, packaging and availability before AVL approval, then validate the connector on the production PCB and in the intended enclosure.
Topology and Physical Packaging
- Interface: 1×4 RJ45 port arrangement with integrated magnetics.
- Mounting: PCB-mounted side-entry assembly.
- Latch: Tab Down; check access after enclosure assembly.
- Indicators: green/yellow.
- Envelope: The record lists 59.12 × 21.30 × 13.55 mm; check the applicable drawing and tolerances.
Magnetics and Electrical Interface
Review the product table for the listed RX/TX turns ratio; the record specifies Ethernet interfaces supporting AutoMDX operation. Match the applicable pinout and center taps to the selected PHY, and confirm isolation and other electrical requirements in the product documentation.
Mechanical Envelope and PCB Layout Considerations
- Access: Allow plug insertion and latch-release clearance at the board edge.
- Footprint: Match signal, shield and retaining holes to the applicable drawing.
- Shield: Review shield and PCB clearance requirements in the host grounding design.
- Indicators: The product record lists green/yellow indicators. Confirm pin assignments and polarity in the applicable schematic and size current limiting for the host supply.
Design Consideration Comparison
| Architecture | Engineering consideration |
|---|---|
| Integrated magnetics RJ45 | The selected connector determines the combined board footprint and magnetic pinout. |
| Discrete connector and magnetics | Component placement and routing depend on the selected connector, transformer and PHY. |
Application Considerations
| Target Application Profile | Primary Engineering Consideration |
|---|---|
| Ethernet equipment | Verify PHY compatibility, signal routing and the board footprint. |
| Enclosed network equipment | Check shield connection, plug access and connector clearance. |
Engineering Verification Checklist
- Compare the PHY interface and transformer pinout with the applicable schematic.
- Check the complete board footprint and board fabrication tolerances.
- Verify shield and retaining-post connections.
- Test mating and latch access in the finished enclosure.
- Verify LED polarity and current limiting.
- Validate isolation, signal integrity and temperature in the assembled system.
Frequently Asked Questions
Which Ethernet speeds are listed for LPJG46801AENL?
The existing product record specifies 10/100/1000 Base-T. Available link modes depend on the host PHY and system configuration.
Can LPJG46801AENL replace 64F-1301GYD2NL?
The existing record positions LPJG46801AENL as a cross-reference and alternative sourcing option for 64F-1301GYD2NL. Compare both official drawings, magnetic characteristics, footprint, LED pins and panel geometry before qualifying a substitution; the listing alone does not prove interchangeability.
What does the side-entry orientation mean for the layout?
Allow plug insertion and latch-release clearance at the board edge. Check the complete multiport footprint, port spacing and mechanical tolerances against the applicable drawing.
What is the listed component operating range?
The product record lists 0°C to 70°C. Assess the finished system separately.
How are the status LEDs driven?
The product record lists green/yellow indicators. Confirm pin assignments and polarity in the applicable schematic and size current limiting for the host supply.
Does LPJG46801AENL support PoE?
The product record specifies Non-PoE. Select a connector and magnetics rated for the required PoE standard when power over Ethernet is needed.
Download
Product Drawing
3D Model
-
Nav Menu
-
About LINK-PP
-
All Products
-
Applications



























