Product Categories
Costa-Rica LINK-PP LQ-AOC11100-3M 100G QSFP28 Active Optical Cable 3m (10ft)
- Compatible Brands: LINK-PP
- Form Factor: QSFP28
- Data Rate: 100G
- Wavelength: 850nm
- Cable Length: 3m
- P/N: LQ-AOC11100-3M
- Manufacture: LINK-PP
- Compatible Brand: LINK-PP
- Compatible P/N: LQ-AOC11100-3M
Category:
Product Description
Product Specifications
| LINK-PP Part Number | LQ-AOC11100-3M | Vendor Name | LINK-PP |
| Form Factor | QSFP28 to QSFP28 | Max Data Rate | 100Gbps |
| Cable Length | 3m (10ft) | Cable Type | Optical Cable |
| Wavelength | 850nm | Minimum Bend Radius | 7.5mm |
| Transmitter Type | VCSEL | Receiver Type | PIN |
| Power supply | 3.3V | CDR | Support |
| Case Temperature | 0 to 70°C | Protocols | 100G Ethernet |
LINK-PP LQ-AOC11100-3M 100G QSFP28 Active Optical Cable (3-Meter, QSFP28 to QSFP28) for Data Center and InfiniBand EDR Interconnects
The LINK-PP LQ-AOC11100-3M is a high-performance, 4-channel, pluggable, parallel 100G QSFP28 Active Optical Cable (AOC) engineered for short-range 100 Gigabit Ethernet and InfiniBand EDR (Enhanced Data Rate) applications. Factory-terminated and pre-sealed with 3 meters (10 feet) of lightweight multimode fiber, this active assembly provides a seamless, plug-and-play interconnect solution for high-density rack environments.
Integrating four independent transmitter and receiver channels operating at data rates up to 25.78Gbps per lane, the cable achieves an aggregate bandwidth of 100Gbps. Built with an 850nm VCSEL laser array, high-sensitivity PIN photodiode receivers, and integrated Clock and Data Recovery (CDR) circuits on both the transmit and receive channels, it guarantees clean eye diagrams and low jitter over short distances. Fully compliant with SFF-8665, SFF-8636, and IEEE 802.3bm 100GBASE-SR4 standards, the LQ-AOC11100-3M offers data center architects a flexible, zero-EMI alternative to bulky copper DAC cables and separate optical transceivers.
Application Topologies and Deployment Scenarios
Active Optical Cables bridge the gap between heavy, reach-limited direct attach copper (DAC) cables and expensive optical transceivers paired with patch cords. The 3-meter length is specifically optimized for high-density, intra-rack and adjacent-rack routing.
In-Rack and Adjacent-Rack ToR-to-Server Interconnects
In modern hyperscale data centers, 100G Top-of-Rack (ToR) switches aggregate traffic from high-performance servers equipped with 100G SmartNICs or PCIe expansion cards. At 3 meters, this AOC provides the ideal span to route from ToR switches down to servers located in the middle or bottom of the same rack, or across to adjacent server cabinets, without cable slack cluttering cable management trays.
High-Density InfiniBand EDR & HPC Compute Clusters
For supercomputing and High-Performance Computing (HPC) clusters utilizing InfiniBand EDR protocol (100Gbps aggregate), low latency and zero packet loss are mandatory. This AOC provides the ultra-wide pipeline and low-jitter signal path required for inter-node communication, storage array uplinks, and clustering compute chassis.
Replacing Bulky Copper DAC Cables in Airflow-Constrained Racks
Passive copper DAC cables at 3 meters become thick (typically 26AWG or 30AWG), heavy, and difficult to bend, severely restricting hot-aisle exhaust airflow. The LQ-AOC11100-3M uses thin optical fiber, reducing cable bundle volume by over 70% and significantly improving chassis airflow efficiency in high-density server racks.
Physical Layer Design and Optoelectronic Architecture
Engineered for continuous commercial operation (0°C to 70°C), this AOC combines advanced micro-optics with highly flexible cable construction.
4-Channel 850nm VCSEL & Integrated CDR Architecture
Each QSFP28 connector head houses an electro-optical engine containing a 4-channel 850nm VCSEL (Vertical-Cavity Surface-Emitting Laser) array and a matched PIN photodiode array. To combat signal degradation over high-speed 25G NRZ electrical host interfaces, both ends of the cable feature integrated TX & RX Clock and Data Recovery (CDR) circuits. The CDR re-times the electrical signals, suppressing jitter and ensuring strict compliance with switch port receiver sensitivity limits.
Ultra-Flexible 7.5mm Bend Radius and Zero EMI Performance
Unlike copper cabling which suffers from signal degradation when bent, the multimode optical fiber core inside this AOC supports a tight minimum bend radius of 7.5mm. This extreme flexibility allows technicians to route cables through tight chassis corners and dense cable organizers without risking micro-bends or link degradation. Furthermore, because data travels as light through dielectric optical fiber, the cable is 100% immune to Electromagnetic Interference (EMI) and radio frequency crosstalk.
Low Power Consumption and Thermal Efficiency
Power efficiency is critical in high-density switch faceplates populated with dozens of 100G ports. Operating from a single +3.3V power supply, this active optical cable consumes significantly less power than driving traditional long-reach optical transceivers, helping to keep switch line card temperatures low.
Multi-Vendor Compatibility and Digital Diagnostics
The LQ-AOC11100-3M is built to strict multi-source agreement specifications, ensuring broad interoperability across enterprise networking hardware.
Open-Standards QSFP28 MSA Interoperability
Compliant with SFF-8665 (QSFP28 mechanical and electrical footprint) and SFF-8636 (management interface), this cable undergoes rigorous validation to guarantee plug-and-play operation across open-networking white-box switches, Arista, Cisco, Dell, Juniper, and generic 100G Ethernet platforms running SONiC, Cumulus, or proprietary NOS software.
Real-Time Digital Diagnostic Monitoring (DOM/DDM)
Integrated DDM functionality accessible via the standard I2C management interface allows network administrators to monitor real-time operating parameters of both connector heads. Telemetry data includes Transceiver Temperature, Vcc Supply Voltage, and individual TX Bias Current, allowing NOC personnel to track cable health via switch CLI or SNMP polling.
Selection Guide and Deployment Considerations
Choosing between DAC, AOC, and optical modules depends on distance, bend radius requirements, and maintenance preferences.
AOC vs. DAC vs. Transceiver + Fiber Patch Cord
- Active Optical Cable (This Product): Pre-terminated, factory-sealed optical assembly. Zero risk of optical end-face contamination (no cleaning required). Lighter and thinner than DAC. Ideal for 3m to 30m in-rack and rack-to-rack interconnects.
- Direct Attach Copper (DAC): Lower cost for very short distances (1m to 2m), but heavy, stiff, and limited in reach due to copper attenuation at 25G per lane.
- Transceivers + Optical Cable: Requires buying two separate 100GBASE-SR4 transceivers and an MPO patch cord. Higher cost and requires strict optical end-face cleaning before insertion.
Cable Routing and Fiber Handling Guidelines
- Bend Radius: Respect the 7.5mm minimum bend radius during installation. Do not tie cable zip-ties too tightly around the optical jacket to avoid crushing internal fiber strands.
- Dust Caps: Leave the protective vinyl dust caps on the QSFP28 connector heads until the exact moment of insertion into the switch port.
- Hot-Pluggable: The cable supports hot-swapping; it can be plugged or unplugged from active switch ports without cycling host system power.
Download
Product Drawing
-
Nav Menu
-
About LINK-PP
-
All Products
-
Applications



























